Brother International BAS-415 Instruction Manual - English - Page 78

Message, editing, Cause, Solution, sewing, communication

Get Brother International BAS-415 PDF manuals and user guides View all Brother International BAS-415 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Message in editing mode Can-'t edit Data Cause 1. Some of data entered in communication mode has items that cannot edit. 2. Some of data entered in sewing mode while reading data has items that cannot edit. 3. According to editing item, there is item that cannot be set. A Solution Refer to page 48. Message in sewing mode No inptted Data Short of Area Data ERR. Area Over B_Thread empty Thread breakage Motor Lock Cause Solution Without sewing data entered, you First, input sewing data, then start try to set machine to sewing mode. sewing. Entered value exceeds maximum This data cannot be sewn. area (450 mm x 285 mm). Entered data has something . wrong. Check where data was made, then contact your dealer. When sewing starts from current needle position, sewing pattern is over area. Move the hoop to position where message disappears, or spread area. The set sewing times in bobbin thread counter is completed_ Reset sewing times in bobbin thread counter. 1. Upper thread breakage. Set thread. 2. Thread is not wound on thread breakage detector. 3. Bobbin thread breakage 4. Bobbin thread has run out. 1. Pulley is too tight. 2. Electrical failure Remove load. Contact your dealer. Message in communication mode Off line Cause 1. Paper tape reader or editing system does not connect with machine by cable. 2. Power of paper tape reader or editing system is not turned on. 3. Editing system does not enter communication mode. 4. Editing system is communicating with an other machine. Solution Link with dedicated cable. Turn on power. Set editing system to communication mode. Wait till communication ends. - 75 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
A
Message
in
editing
mode
Cause
Solution
Can
-'t
edit
Data
1.
Some
of
data
entered
in
communication
mode
has
items
that
cannot
edit.
Refer
to
page
48.
2.
Some
of
data
entered
in
sewing
mode
while
reading
data
has
items
that
cannot
edit.
3.
According
to
editing
item,
there
is
item
that
cannot
be
set.
Message
in
sewing
mode
Cause
Solution
No
inptted
Data
Without
sewing
data
entered,
you
First,
input
sewing
data,
then
start
try
to
set
machine
to
sewing
mode.
sewing.
Short
of
Area
Entered
value
exceeds
maximum
area
(450
mm
x
285
mm).
This
data
cannot
be
sewn.
Data
ERR.
Entered
data
has
something
.
Check
where
data
was
made,
then
wrong.
contact
your
dealer.
Area
Over
When
sewing
starts
from
current
Move
the
hoop
to
position
where
needle
position,
sewing
pattern
is
message
disappears,
or
spread
over
area.
area.
B_Thread
empty
The
set
sewing
times
in
bobbin
Reset
sewing
times
in
bobbin
thread
counter
is
completed_
thread
counter.
Thread
breakage
1.
Upper
thread
breakage.
Set
thread.
2.
Thread
is
not
wound
on
thread
breakage
detector.
3.
Bobbin
thread
breakage
4.
Bobbin
thread
has
run
out.
Motor
Lock
1.
Pulley
is
too
tight.
Remove
load.
2.
Electrical
fai
lure
Contact
your
dealer.
Message
in
communication
mode
Cause
Solution
Off
line
1.
Paper
tape
reader
or
editing
system
does
not
connect
with
machine
by
cable.
Link
with
dedicated
cable.
2.
Power
of
paper
tape
reader
or
editing
system
is
not
turned
on.
Turn
on
power.
3.
Editing
system
does
not
enter
Set
editing
system
to
communication
mode.
communication
mode.
4.
Editing
system
is
communicating
with
an
other
machine.
Wait
till
communication
ends.
-
75
-