Compaq ProLiant 6500 Compaq Parallel Database Cluster Model PDC/05000 for Orac - Page 123

Verifying Array Controller Properties, Displaying SCSI Devices in the Devices Windowpane, Windowpane

Get Compaq ProLiant 6500 PDF manuals and user guides View all Compaq ProLiant 6500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 123 highlights

Installation and Configuration 5-27 To discover the disk drives: 1. From the CLI window, type the following and press Enter: run config 2. Wait a few minutes for the array controller to scan and discover the installed disk drives. 3. Once the access LED on each drive has blinked, press Enter to return to the command prompt in the CLI window. 4. Type the following and press Enter: show devices 5. Verify the devices discovered are consistent with the installed disk drives. The disk drives will be named in the DISK##### format. Refer to the Compaq StorageWorks documentation for the naming conventions for storage subsystem devices. 6. Close the CLI window. Verifying Array Controller Properties Displaying SCSI Devices in the Devices Windowpane 1. Click on the Windows taskbar Start button. 2. Select Program, Command Console, HSG80 Storage Window. 3. Select Serial Communication and click OK. 4. Select baud rate of 9600 and click Connect. NOTE: If you receive a pop-up window reading "Error scanning subsystem," wait two minutes and retry the connection. SWCC finds installed devices and displays them in a grid. Verifying Controller Properties 1. Double-click a controller icon in the Storage Window to display Controller Properties. Click on the tabs of the Controller Properties screen to confirm that the values in Table 5-1 are set.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
Installation and Configuration
5-27
To discover the disk drives:
1.
From the CLI window, type the following and press
Enter:
run config
2.
Wait a few minutes for the array controller to scan and discover the
installed disk drives.
3.
Once the access LED on each drive has blinked, press
Enter
to return to
the command prompt in the CLI window.
4.
Type the following and press
Enter:
show devices
5.
Verify the devices discovered are consistent with the installed disk
drives.
The disk drives will be named in the DISK##### format. Refer to the
Compaq StorageWorks documentation for the naming conventions for
storage subsystem devices.
6.
Close the CLI window.
Verifying Array Controller Properties
Displaying SCSI Devices in the Devices
Windowpane
1.
Click on the Windows taskbar
Start
button.
2.
Select
Program,
Command Console, HSG80 Storage Window.
3.
Select
Serial Communication
and click
OK.
4.
Select baud rate of 9600 and click
Connect.
NOTE:
If you receive a pop-up window reading
“
Error scanning subsystem,
”
wait two
minutes and retry the connection.
SWCC finds installed devices and displays them in a grid.
Verifying Controller Properties
1.
Double-click a controller icon in the Storage Window to display
Controller Properties. Click on the tabs of the
Controller Properties
screen to confirm that the values in Table 5-1 are set.