Compaq ProLiant 6500 Compaq Parallel Database Cluster Model PDC/05000 for Orac - Page 175

Preparing the Replacement Node, Install and con Windows 2000 Advanced Server with Service

Get Compaq ProLiant 6500 PDF manuals and user guides View all Compaq ProLiant 6500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 175 highlights

Cluster Management 6-21 Preparing the Replacement Node Several steps should be performed on the replacement server before it is integrated into the cluster. Prior to integrating the server into the cluster, perform the following steps: 1. Connect the replacement server to the cluster interconnect and to the client LAN. Power on the server. Although physically connected to the cluster, the server is not yet integrated into the cluster. IMPORTANT: Do not connect the server to the Storage Hubs or Fibre Channel SAN Switches yet. 2. Start the replacement node with the Compaq SmartStart and Support Software CD in the CD-ROM drive. 3. Use the Compaq System Configuration Utility to configure the hardware settings of the node and its adapters. 4. Use the Compaq Array Configuration Utility to configure the node's local non-shared disks with RAID. 5. Install and configure Windows 2000 Advanced Server with Service Pack 1 or later. 6. Install necessary Compaq drivers and utilities from the Compaq SmartStart and Support Software CD. 7. Enter unique IP addresses and node names for each node in the hosts and lmhosts files located at %SystemRoot%\system32\drivers\etc. 8. Install the host adapter drivers. 9. Install the Fibre Channel Software Setup (FCSS) utility. 10. Install and configure Secure Path for Windows 2000.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
Cluster Management
6-21
Preparing the Replacement Node
Several steps should be performed on the replacement server before it is
integrated into the cluster.
Prior to integrating the server into the cluster, perform the following steps:
1.
Connect the replacement server to the cluster interconnect and to the
client LAN. Power on the server. Although physically connected to the
cluster, the server is not yet integrated into the cluster.
IMPORTANT:
Do not connect the server to the Storage Hubs or Fibre Channel SAN
Switches yet.
2.
Start the replacement node with the Compaq SmartStart and Support
Software CD in the CD-ROM drive.
3.
Use the Compaq System Configuration Utility to configure the hardware
settings of the node and its adapters.
4.
Use the Compaq Array Configuration Utility to configure the node
’
s
local non-shared disks with RAID.
5.
Install and configure Windows 2000 Advanced Server with Service
Pack 1 or later.
6.
Install necessary Compaq drivers and utilities from the Compaq
SmartStart and Support Software CD.
7.
Enter unique IP addresses and node names for each node in the hosts
and lmhosts files located at %SystemRoot%\system32\drivers\etc.
8.
Install the host adapter drivers.
9.
Install the Fibre Channel Software Setup (FCSS) utility.
10.
Install and configure Secure Path for Windows 2000.