Cub Cadet XT2 GX50 Operation Manual - Page 9

Hood Topper Not Shown for Clarity

Get Cub Cadet XT2 GX50 PDF manuals and user guides View all Cub Cadet XT2 GX50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

ASSEMBLY INSTALLING THE HOOD COLLAR (IF NECESSARY) There are three (3) alignment posts (a) on the hood collar (b) that line up with corresponding alignment holes (c) in the hood (d). See Figure 5. (c) (a) (b) (d) 3. Once the hood topper is in place, the two locking tabs near the rear of the hood need to be pushed upward to lock the hood topper in place. See Figure 8. (c) (c) (a) (a) (a) Figure 5 Use these alignment points to properly position the hood collar (a), then secure it in place with the six hex bolts (b) provided in the hardware bag. Tighten the hex bolts to 102-124 in-lbs (11.514 N-m). See Figure 6. a bb b b Hood Topper Not Shown for Clarity Figure 8 INSTALLING THE SCREW-ON HOOD TOPPER (IF NECESSARY) NOTE: Be careful not to damage the headlight harness when installing the screw-on hood topper. 1. Set the hood topper up against the top of the hood with the hood open, and align the holes on the hood. 2. Secure the screw-on hood topper (a) from below, handtighten the screws (b) on the rear half of the hood and then snug them. See Figure 9. 3. With the rear screws in place, align the holes in the hood topper (a) with the holes in the hood (c) and secure in place with remaining two screws (d). See Figure 9. (a) (c) Figure 6 INSTALLING THE SNAP-ON HOOD TOPPER (IF NECESSARY) 1. To install the snap-on hood topper (a), line up the holes on the hood topper (a) with the tabs (b) in the hood frame as shown in Figure 7. (a) (b) (b) (b) (b) (b) (b) (d) (d) Figure 9 4. Tighten all four screws to 16-24 in-lbs (1.8-2.7 N-m). INSTALLING THE PLENUM (IF NECESSARY) NOTE: Be careful not to damage the headlight harness when installing the plenum. To install the plenum (a) onto the hood (b): 1. Insert the rear tabs (c) as shown in Figure 10. Figure 7 (c) (b) 2. Insert the tabs (b) into the hood topper and pull back to lock (a) into place. Figure 10 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
9
ASSEMBLY
INSTALLING THE HOOD COLLAR ±IF NECESSARY²
There are three (3) alignment posts (a) on the hood collar (b) that
line up with corresponding alignment holes (c) in the hood (d).
See Figure 5.
(a)
(a)
(a)
(a)
(b)
(c)
(c)
(c)
(d)
Figure 5
Use these alignment points to properly position the hood collar
(a), then secure it in place with the six hex bolts (b) provided in
the hardware bag. Tighten the hex bolts to 102-124 in-lbs (11.5-
14 N-m). See Figure 6.
b
a
b
b
b
Figure 6
INSTALLING THE SNAP³ON HOOD TOPPER ±IF NECESSARY²
1.
To install the snap-on hood topper (a), line up the holes on
the hood topper (a) with the tabs (b) in the hood frame as
shown in Figure 7.
(a)
(b)
(b)
(b)
(b)
Figure 7
2.
Insert the tabs (b) into the hood topper and pull back to lock
into place.
3.
Once the hood topper is in place, the two locking tabs near
the rear of the hood need to be pushed upward to lock the
hood topper in place. See Figure 8.
Hood Topper Not Shown for Clarity
Figure 8
INSTALLING THE SCREW³ON HOOD TOPPER
±IF NECESSARY²
NOTE:
Be careful not to damage the headlight harness when
installing the screw-on hood topper.
1.
Set the hood topper up against the top of the hood with the
hood open, and align the holes on the hood.
2.
Secure the screw-on hood topper (a) from below, hand-
tighten the screws (b) on the rear half of the hood and then
snug them. See Figure 9.
3.
With the rear screws in place, align the holes in the hood
topper (a) with the holes in the hood (c) and secure in place
with remaining two screws (d). See Figure 9.
(a)
(b)
(b)
(d)
(c)
(d)
Figure 9
4.
Tighten all four screws to 16-24 in-lbs (1.8-2.7 N-m).
INSTALLING THE PLENUM ±IF NECESSARY²
NOTE:
Be careful not to damage the headlight harness when
installing the plenum.
To install the plenum (a) onto the hood (b):
1.
Insert the rear tabs (c) as shown in Figure 10.
(b)
(a)
(c)
Figure 10