D-Link DSN-3400-10 User's Manual for DSN-3200-10 Valid for firmware 1.6.1 - Page 76

Create Network Portal Wizard - Set the IP Address Screen, Table 5-10 Create Network

Get D-Link DSN-3400-10 - xStack Storage Area Network Array Hard Drive PDF manuals and user guides
UPC - 790069299766
View all D-Link DSN-3400-10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Figure 5-25Create Network Portal Wizard - Set the IP Address Screen 3. Complete the fields in the screen (see Table 5-10). 4. Click the Finish button. 5. If more than one data port will be communicating with your iSCSI initiator, repeat this procedure for each data port, making sure to assign the appropriate IP address for each data port. After you create the network portals, you can monitor their status using the Portals Information screen (see Section 6.15). Table 5-10 Create Network Portal Wizard - Set the IP Address Screen Settings Setting IP Address Subnet Mask Default Gateway Description Enter the IP address for the network portal. The IP address must be a unique address that is different than the management port and on the same subnet as the iSCSI initiator. Enter a subnet mask for the network portal or press the Tab key to automatically accept the default subnet mask. If a router is required for the xStack Storage Array to reach the initiator(s), the default gateway must have the IP address of that router. In a network that requires a router between the xStack Storage Array and the initiator, enter the router's IP address. In a network that uses only direct connection, or a switch between the xStack Storage Array and the initiator(s), no entry is required. 76 Chapter 5 Configuring the xStack Storage Array

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
76
Chapter 5
Configuring
the xStack Storage Array
Figure 5-25Create Network Portal Wizard – Set the IP Address Screen
3.
Complete the fields in the screen (see Table 5-10).
4.
Click the
Finish
button.
5.
If more than one data port will be communicating with your iSCSI initiator, repeat this
procedure for each data port, making sure to assign the appropriate IP address for each data
port.
After you create the network portals, you can monitor their status using the
Portals Information screen (see Section 6.15).
Table 5-10 Create Network Portal Wizard – Set the IP Address Screen Settings
Setting
Description
IP Address
Enter the IP address for the network portal. The IP address must be a unique address
that is different than the management port and on the same subnet as the iSCSI
initiator.
Subnet Mask
Enter a subnet mask for the network portal or press the Tab key to automatically accept
the default subnet mask.
Default Gateway
If a router is required for the xStack Storage Array to reach the initiator(s), the default
gateway must have the IP address of that router. In a network that requires a router
between the xStack Storage Array and the initiator, enter the router’s IP address. In a
network that uses only direct connection, or a switch between the xStack Storage Array
and the initiator(s), no entry is required.