Dell 1135N Service Manual - Page 122
JAM 2
 |
View all Dell 1135N manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 122 highlights
Alignment and Troubleshooting 4) JAM 2 Description : 1. Recording paper is jammed in front of or inside the fuser. 2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the Actuator-Feed. 1. If the paper is rolled in the Fuser Roller: - This occurs when a Guide claw is broken away or transformed. - It occurs when the Heat-Roller or Pressure-Roller is seriously contaminated with the toner. 2. Check the Exit roller is transformed or contaminated. Refer to JAM2 flow chart in fuser problem troubleshooting. Replace the Exit roller. Service Manual 4-49
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117 -
118 -
119 -
120 -
121 -
122 -
123 -
124 -
125 -
126 -
127 -
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
 |
 |
Alignment and Troubleshooting
4-49
Service Manual
4) JAM 2
Description :
1. Recording paper is jammed in front of or inside the fuser.
2.
Recording paper is stuck in the discharge roller and in the fuser just after
passing through the Actuator-Feed.
2. Check the Exit roller is
transformed or contaminated.
1. If the paper is
rolled in the Fuser Roller:
- This occurs when a Guide claw is
broken away or transformed.
- It occurs when the Heat-Roller or
Pressure-Roller is seriously
contaminated
with the toner.
Refer to JAM2 flow chart
in fuser problem troubleshooting.
Replace the Exit roller.