Dell Alienware m17 R3 Service Manual - Page 39

CAUTION: Place the computer on a soft and clean surface to avoid scratching the display.

Get Dell Alienware m17 R3 PDF manuals and user guides View all Dell Alienware m17 R3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Steps 1. Remove the screw (M2x3) that secures the wireless card bracket to the left I/O-board. 2. Lift the wireless card bracket off the left I/O-board. 3. Disconnect the antenna cables from the wireless card. 4. Peel the tapes securing the antenna cables to system board and left fan. 5. Remove the antenna cables from the routing guides on the left fan and system board. 6. Peel the tapes securing the display cable to the system board. 7. Open the latch, and disconnect the display cable from the connector on the system board. 8. Disconnect the G-sensor cable from the connector on the system board. 9. Disconnect the Tobii eye tracker cable from the connector on the system board. NOTE: This step is only applicable to computers shipped with a Tobii eye tracker. 10. Place the computer face up. CAUTION: Place the computer on a soft and clean surface to avoid scratching the display. 11. Remove the following cables from the routing guides on the palm-rest assembly. • Display cable • G-sensor cable • Tobii eye tracker cable 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
Steps
1.
Remove the screw (M2x3) that secures the wireless card bracket to the left I/O-board.
2.
Lift the wireless card bracket off the left I/O-board.
3.
Disconnect the antenna cables from the wireless card.
4.
Peel the tapes securing the antenna cables to system board and left fan.
5.
Remove the antenna cables from the routing guides on the left fan and system board.
6.
Peel the tapes securing the display cable to the system board.
7.
Open the latch, and disconnect the display cable from the connector on the system board.
8.
Disconnect the G-sensor cable from the connector on the system board.
9.
Disconnect the Tobii eye tracker cable from the connector on the system board.
NOTE: This step is only applicable to computers shipped with a Tobii eye tracker.
10.
Place the computer face up.
CAUTION: Place the computer on a soft and clean surface to avoid scratching the display.
11.
Remove the following cables from the routing guides on the palm-rest assembly.
•
Display cable
•
G-sensor cable
•
Tobii eye tracker cable
39