Dell Alienware m17 R3 Service Manual - Page 54

Power-adapter port, Removing the power-adapter port

Get Dell Alienware m17 R3 PDF manuals and user guides View all Dell Alienware m17 R3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Steps 1. Place the fan and heat-sink assembly on the system board. 2. In sequential order (1>2>3>4>5>6>7>8>9>10), replace the ten screws (M2x3) that secure the fan and heat-sink assembly to the system board. NOTE: The number of screws varies depending on the configuration ordered. 3. Connect the left and right fan cables to the system board. Next steps 1. Follow step 3 to step 22 in installing the system board. 2. Install the battery. 3. Install the rear I/O-cover. 4. Install the 2280 solid-state drive in M.2 slot two, if installed. 5. Install the 2230 solid-state drive in M.2 slot two, if installed. 6. Install the 2280 solid-state drive in M.2 slot one, if installed. 7. Install the 2230 solid-state drive in M.2 slot one, if installed. 8. Install the base cover. 9. Follow the procedure in After working inside your computer. Power-adapter port Removing the power-adapter port Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the 2230 solid-state drive in M.2 slot one, if installed. 4. Remove the 2280 solid-state drive in M.2 slot one, if installed. 5. Remove the 2230 solid-state drive in M.2 slot two, if installed. 6. Remove the 2280 solid-state drive in M.2 slot two, if installed. 7. Remove the rear I/O-cover. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
Steps
1.
Place the fan and heat-sink assembly on the system board.
2.
In sequential order (1>2>3>4>5>6>7>8>9>10), replace the ten screws (M2x3) that secure the fan and heat-sink assembly to
the system board.
NOTE: The number of screws varies depending on the configuration ordered.
3.
Connect the left and right fan cables to the system board.
Next steps
1.
Follow step 3 to step 22 in installing the
system board
.
2.
Install the
battery
.
3.
Install the
rear I/O-cover
.
4.
Install the
2280 solid-state drive in M.2 slot two
, if installed.
5.
Install the
2230 solid-state drive in M.2 slot two
, if installed.
6.
Install the
2280 solid-state drive in M.2 slot one
, if installed.
7.
Install the
2230 solid-state drive in M.2 slot one
, if installed.
8.
Install the
base cover
.
9.
Follow the procedure in
After working inside your computer
.
Power-adapter port
Removing the power-adapter port
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
2230 solid-state drive in M.2 slot one
, if installed.
4.
Remove the
2280 solid-state drive in M.2 slot one
, if installed.
5.
Remove the
2230 solid-state drive in M.2 slot two
, if installed.
6.
Remove the
2280 solid-state drive in M.2 slot two
, if installed.
7.
Remove the
rear I/O-cover
.
54