Dell Dimension 8250 Dell Dimension 8250 Owner's Manual - Page 102

device and the device connected to the middle connector is the slave

Page 102 highlights

www.dell.com | support.dell.com 12 Connect a power cable to the drive. NOTICE: Match the colored strip on the cable with pin 1 on the drive. 13 Locate the extra connector on the drive cable that is attached to your first hard drive and attach the connector to the second hard drive. Your computer uses cable-select drive cables. This means that the device connected to the end connector of the drive cable is the master device and the device connected to the middle connector is the slave device. Be sure that the jumper setting on the new device is set for "cable select" (see the documentation that came with the drive for information). power cable second hard-drive cable (secondary drive) first hard-drive cable (primary boot drive) 14 Close the computer cover. NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer. 15 Connect your computer and devices to electrical outlets, and turn them on. 102 A d d i n g Pa r ts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156

102
Adding Parts
www.dell.com | support.dell.com
12
Connect a power cable to the drive.
NOTICE:
Match the colored strip on the cable with pin 1 on the drive.
13
Locate the extra connector on the drive cable that is attached to your
first hard drive and attach the connector to the second hard drive.
Your computer uses cable-select drive cables. This means that the
device connected to the end connector of the drive cable is the master
device and the device connected to the middle connector is the slave
device. Be sure that the jumper setting on the new device is set for
"cable select" (see the documentation that came with the drive for
information).
14
Close the computer cover.
NOTICE:
To connect a network cable, first plug the cable into the network
wall jack and then plug it into the computer.
15
Connect your computer and devices to electrical outlets, and turn
them on.
power cable
first hard-drive
cable (primary
boot drive)
second hard-drive
cable (secondary
drive)