Dell Force10 E600i E600i System Installation Guide - Page 34

To remove an SFM, TSM-6-SFM_REMOVE: Removed SFM

Get Dell Force10 E600i PDF manuals and user guides View all Dell Force10 E600i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

www.dell.com | support.dell.com Step Task 4 Hold the card by the edges. Avoid touching the printed circuit board and connector pins. Slide the card out of the slot, and store the card in the original anti-static packaging. 5 If you are not planning to install a new card immediately, install a blank panel. To remove an SFM: Step 1 2 3 Task Loosen the captive screw and pull the ejector lever towards you to disengage the backplane connections. Slide the card out of the slot and store it in the original anti-static packaging. System messages appear on the console, including the following: %TSM-6-SFM_REMOVE: Removed SFM Wait 5 to 10 seconds to install a new SFM or reinsert an SFM. * NOTE: If you mistakenly insert an SFM too quickly after removing it, traffic flow is interrupted. To correct the situation, remove an active SFM or the standby SFM, wait several seconds, and reinsert. System messages stating that the active interfaces' status changed and that the switch fabric is up appear when an fifth SFM is inserted correctly and traffic is flowing. If you are not planning to install a new card immediately, install a blank panel. 34 | Installing RPMs, Line Cards, and SFMs

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
34
|
Installing RPMs, Line Cards, and SFMs
www.dell.com | support.dell.com
To remove an SFM:
4
Hold the card by the edges. Avoid touching the printed circuit board and connector pins. Slide the card out of the
slot, and store the card in the original anti-static packaging.
5
If you are not planning to install a new card immediately, install a blank panel.
Step
Task
1
Loosen the captive screw and pull the ejector lever towards you to disengage the backplane connections.
2
Slide the card out of the slot and store it in the original anti-static packaging. System messages appear on the
console, including the following:
%TSM-6-SFM_REMOVE: Removed SFM
Wait 5 to 10 seconds to install a new SFM or reinsert an SFM. *
NOTE:
If you mistakenly insert an SFM too quickly after removing it, traffic flow is interrupted. To correct the
situation, remove an active SFM or the standby SFM, wait several seconds, and reinsert. System messages stating
that the active interfaces’ status changed and that the switch fabric is up appear when an fifth SFM is inserted
correctly and traffic is flowing.
3
If you are not planning to install a new card immediately, install a blank panel.
Step
Task