Home » Dell Manuals » Servers » Dell Force10 E600i » Manual Viewer

Dell Force10 E600i E600i System Installation Guide - Page 38

Connecting to the 10/100 Ethernet Management Port, 100 Ethernet

Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

www.dell.com | support.dell.com Table 8-5. RJ-45 to DB-25 Adapter Pin Assignments E-Series Auxiliary Port Signal DTR TxD GND GND RxD DSR CTS RJ-45 to RJ-45 Rollover Cable RJ-45 Pinout 2 3 4 5 6 7 8 RJ-45 Pinout 7 6 5 4 3 2 1 RJ-45 to DB-25 Modem Adapter DB-45 Pinout 20 3 7 7 2 8 5 Modem Signal DTR TxD GND GND RxD DCD CTS Connecting to the 10/100 Ethernet Management Port Configure the 10/100 Ethernet management port, labeled 10/100 Ethernet on the primary RPM card in to obtain network access to the chassis for management functions like upgrading the FTOS image. Table 8-6. 10/100 Ethernet Management Port LEDs Label L (Link) A (Activity) Description Lit: Link is up. Unlit: No connection Lit: Activity on port. Unlit: No activity 38 | RPM Ports and Cables

Section	Page
About This Guide	7
Information Symbols	7
Related Publications	7
The E600i System	9
System Overview	9
Install the E600i Chassis	12
Site Preparation	13
Site Selection	13
Equipment Rack and Cabinet Requirements	13
Power Requirements	14
2500W AC Power Requirements	14
DC Power Requirements	14
Storage Requirements	14
Chassis	15
Install the Chassis	15
Unpack the System Components	15
Install the Equipment Rack Shelf Bar	15
Mount the Chassis in a Rack	16
Mount the Chassis in a Cabinet	17
Fan Tray	19
Install the Fan Tray	20
Remove the Fan Tray	20
Power Supply	21
AC Power Supply Units	22
Power Cord Requirements	23
Install the AC Power Supply Units	23
Remove the AC Power Supply	24
DC Power Entry Modules	25
Cable and Connector Requirements	25
Install the DC PEMs	25
Replace the DC PEM	26
Installing RPMs, Line Cards, and SFMs	29
Route Processor Modules	29
RPM LEDs	29
Line Cards	30
Line Card LEDs	30
Switch Fabric Modules	30
SFM Front Panel and LEDs	31
Blank Panels	31
Install RPMs, Line Cards, and SFMs	32
Remove RPMs, Line Cards, and SFMs	33
RPM Ports and Cables	35
Connecting to the Console and Auxiliary Ports	35
Cable and Adapter Pin Assignments	35
Accessing the Console with a DB-9 Adapter	36
Accessing the Console with a DB-25 Adapter	37
Accessing the Auxiliary Port by Modem	37
Connecting to the 10/100 Ethernet Management Port	38
Air Filter	39
Using a Flash Memory Card	41
External Flash Memory Card Overview	41
Inserting the External Flash Memory Card	41
Removing the External Flash Memory Card	41
Formatting an External Flash Card	42
Copying Files to the External Flash	42
Displaying Files Stored on the External Flash	42
System Boot	45
The E-Series System Boot Process	45
Booting from the BOOT_USER Prompt	45
Alarms	51
AC Power Supplies and Alarms	52
SFMs and Alarms	53
System Specifications	55
Chassis Physical Design	55
Environmental	56
AC Power Supply Unit Requirements	56
DC Power Entry Module Requirement	57
SFM and RPM Power Requirements	57
Agency Compliance	57
Safety Standards and Compliance Agency Certifications	59
Electromagnetic Compatibility (EMC)	59
Product Recycling and Disposal	60
Technical Support	61
The iSupport Website	61
Accessing iSupport Services	61
Contacting the Technical Assistance Center	62
Requesting a Hardware Replacement	62