Dell PowerEdge M1000e Dell PowerEdge M1000e Configuration Guide - Page 27

Initial System Configuration, Before You Begin, Power Requirements, Network Information, Initial - manual

Get Dell PowerEdge M1000e PDF manuals and user guides View all Dell PowerEdge M1000e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

2 Initial System Configuration Before You Begin Power Requirements CAUTION: The enclosure power supplies must be connected to a Type B or permanently-connected PDU and not directly to an electrical outlet. The power supplies require a 100-120 V or 200-240 V power source. You can select only one AC power input, as the system does not operate at both ranges simultaneously. Network Information If your network uses static addressing, you need the IP address, subnet mask, and gateway to configure the CMC and other modules in the enclosure. Initial Setup Sequence 1 Unpack the enclosure and install it in a rack. For more information, see the Getting Started Guide and Rack Installation Guide at support.dell.com/manuals. CAUTION: Do not turn on the blades (server modules) until you have configured the switch modules, as described in "Configuring the I/O Modules" on page 47. 2 Connect the power supply units to a PDU. 3 If an optional iKVM module is installed, connect the keyboard, video, and mouse to the enclosure control panel (see Figure 1-4) or to the iKVM module (see Figure 1-16). NOTE: Connecting a keyboard, video, and mouse to the enclosure front panel disables video output to the iKVM back panel port. 4 Press the power button on the enclosure control panel. See Figure 1-4. Initial System Configuration 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Initial System Configuration
27
2
Initial System Configuration
Before You Begin
Power Requirements
CAUTION:
The enclosure power supplies must be connected to a Type B or
permanently-connected PDU and not directly to an electrical outlet. The power
supplies require a 100–120 V or 200–240 V power source. You can select only one
AC power input, as the system does not operate at both ranges simultaneously.
Network Information
If your network uses static addressing, you need the IP address, subnet mask,
and gateway
to configure the CMC and other modules in the enclosure.
Initial Setup Sequence
1
Unpack the enclosure and install it in a rack.
For more information, see the
Getting Started Guide
and
Rack Installation
Guide
at
support.dell.com/manuals
.
CAUTION:
Do not turn on the blades (server modules) until you have configured
the switch modules, as described in "Configuring the I/O Modules" on page 47.
2
Connect the power supply units to a PDU.
3
If an optional iKVM module is installed, connect the keyboard, video, and
mouse to the enclosure control panel (see Figure 1-4) or to the iKVM
module (see Figure 1-16).
NOTE:
Connecting a keyboard, video, and mouse to the enclosure front panel
disables video output to the iKVM back panel port.
4
Press the power button on the enclosure control panel. See Figure 1-4.