Dell PowerEdge M1000e Dell PowerEdge M1000e Configuration Guide - Page 29

Protocol IPv4 and/or IPv6, Start the LCD Configuration Wizard. - ikvm

Get Dell PowerEdge M1000e PDF manuals and user guides View all Dell PowerEdge M1000e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

NOTE: The option to configure the enclosure using the LCD Configuration Wizard is only available until the CMC default password is changed or when the LCD Configuration Wizard is complete. Thereafter, use the RACADM CLI or the webbased GUI to change the CMC settings (see "Configuring the CMC Network Settings Using a Management Station and CLI" on page 30). NOTE: The serial null modem cable for the CMC is an option. You can access the CLI using the 17th Blade feature on the embedded iKVM module. Blade number 17 is a direct local connection to the CMC. 1 Choose a language from the options presented in the dialog box. 2 Start the LCD Configuration Wizard. 3 Configure the CMC network settings for your network environment. NOTE: The CMC external management network mode is set by default to DHCP. To use a static IP address, you must change the setting using the LCD Configuration Wizard. - Network speed - Duplex mode - Protocol (IPv4 and/or IPv6) - Network mode (DHCP or static) - Static IP address, subnet mask, and gateway values (if static mode was selected) - DNS setting, including a registered CMC name, (if DHCP mode was selected) 4 If required, configure the iDRAC network setting for DHCP mode. NOTE: You cannot set a static IP address for the iDRAC using the LCD Configuration Wizard. See "Configuring iDRAC Networking Using the WebBased Interface" on page 33. Initial System Configuration 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Initial System Configuration
29
NOTE:
The option to configure the enclosure using the LCD Configuration Wizard is
only available until the CMC default password is changed or when the LCD
Configuration Wizard is complete. Thereafter, use the RACADM CLI or the web-
based GUI to change the CMC settings (see "Configuring the CMC Network Settings
Using a Management Station and CLI" on page 30).
NOTE:
The serial null modem cable for the CMC is an option. You can access the
CLI using the 17th Blade feature on the embedded iKVM module. Blade number 17 is
a direct local connection to the CMC.
1
Choose a language from the options presented in the dialog box.
2
Start the LCD Configuration Wizard.
3
Configure the CMC network settings for your network environment.
NOTE:
The CMC external management network mode is set by default to
DHCP. To use a static IP address, you must change the setting using the LCD
Configuration Wizard.
–
Network speed
–
Duplex mode
–
Protocol (IPv4 and/or IPv6)
–
Network mode (DHCP or static)
–
Static IP address, subnet mask, and gateway values (if static mode was
selected)
–
DNS setting, including a registered CMC name, (if DHCP mode was
selected)
4
If required, configure the iDRAC network setting for DHCP mode.
NOTE:
You cannot set a static IP address for the iDRAC using the LCD
Configuration Wizard. See "Configuring iDRAC Networking Using the Web-
Based Interface" on page 33.