Dell PowerEdge M1000e Dell PowerEdge M1000e Configuration Guide - Page 53

Dell PowerConnect-KR 8024-k Switch, Setup, Configuring, I/O Modules Network Settings

Get Dell PowerEdge M1000e PDF manuals and user guides View all Dell PowerEdge M1000e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

3 Select the Setup tab. The Configuring I/O Modules Network Settings page is displayed. 4 Configure the switch for integration into your network. - Select DHCP Mode Enabled if your network uses a DHCP server to assign IP addresses. - If your network uses static IP addressing, enter an IP address, subnet mask and gateway. 5 When you have finished, click Apply. 6 Click the Deploy sub-tab. After all I/O modules have been configured and connected, the enclosure's blades can be inserted and booted with full network communication. Dell PowerConnect-KR 8024-k Switch The PowerConnect M8024-k switch provides 16 internal 10 GbE ports, four external 10 GbE SFP+ ports, and one 10 GbE expansion slot for 10 GbE external uplinks. The expansion slot on the front panel can support: • A 10 Gb Ethernet module with four optical SFP+ connectors • A 10 Gb Ethernet module with three copper CX4 uplinks • A 10 Gb Ethernet module with two copper 10GBASE-T uplinks This module is hot-swappable and may be installed in Fabric A, B, or C. Configuring the I/O Modules 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Configuring the I/O Modules
53
3
Select the
Setup
tab. The
Configuring
I/O Modules Network Settings
page is displayed.
4
Configure the switch for integration into your network.
–
Select
DHCP Mode Enabled
if your network uses a DHCP server to
assign IP addresses.
–
If your network uses static IP addressing, enter an IP address, subnet
mask and gateway.
5
When you have finished, click
Apply
.
6
Click the
Deploy
sub-tab.
After all I/O modules have been configured and connected, the enclosure’s
blades can be inserted and booted with full network communication.
Dell PowerConnect-KR 8024-k Switch
The PowerConnect M8024-k switch provides 16 internal 10 GbE ports, four
external 10 GbE SFP+ ports, and one 10 GbE expansion slot for 10 GbE
external uplinks. The expansion slot on the front panel can support:
•
A 10 Gb Ethernet module with four optical SFP+ connectors
•
A 10 Gb Ethernet module with three copper CX4 uplinks
•
A 10 Gb Ethernet module with two copper 10GBASE-T uplinks
This module is hot-swappable and may be installed in Fabric A, B, or C.