Epson 2080 User Manual - Page 164

the high-capacity cut-sheet feeder, see the next To load paper in

Get Epson 2080 - LQ B/W Dot-matrix Printer PDF manuals and user guides View all Epson 2080 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 164 highlights

3. Press up the tabs on both sides of the paper tension unit and lift it up and off the printer. If a tractor is installed in the pull position, remove it as described on page 2-30. Store any printer parts you remove in a safe place. 4. Hold the cut-sheet feeder in both hands and fit the feeder's notches over the mounting posts on the printer as shown below. Then release the latch levers and lower the cut-sheet feeder until it rests on the printer. A 5. Insert the cable into the connector as shown above. 6. Replace the printer cover. You are now ready to load paper in the cut-sheet feeder. To load paper in the high-capacity cut-sheet feeder, see the next section. To load paper in the second bin of the double-bin cut-sheet feeder, see the manual that comes with the second-bin cut-sheet feeder. If you installed the double-bin cutsheet feeder, you need to select the paper source (bin 1 or bin 2) as described on page A-10. To remove the cut-sheet feeder, reverse the steps above. Enhancing Your Printer With Options A-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
A
Enhancing Your Printer With Options
A-5
3.
Press up the tabs on both sides of the paper tension unit and lift it up
and off the printer. If a tractor is installed in the pull position, remove
it as described on page 2-30. Store any printer parts you remove in a
safe place.
4.
Hold the cut-sheet feeder in both hands and fit the feeder’s notches over
the mounting posts on the printer as shown below. Then release the
latch levers and lower the cut-sheet feeder until it rests on the printer.
5.
Insert the cable into the connector as shown above.
6.
Replace the printer cover.
You are now ready to load paper in the cut-sheet feeder. To load paper in
the high-capacity cut-sheet feeder, see the next section. To load paper in the
second bin of the double-bin cut-sheet feeder, see the manual that comes
with the second-bin cut-sheet feeder. If you installed the double-bin cut-
sheet feeder, you need to select the paper source (bin 1 or bin 2) as described
on page A-10.
To remove the cut-sheet feeder, reverse the steps above.