Epson PowerLite Pro Z8455WUNL Operation Guide - EasyMP Network Projection - Page 32

Connecting to a Projector on a Different Subnet

Get Epson PowerLite Pro Z8455WUNL PDF manuals and user guides View all Epson PowerLite Pro Z8455WUNL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Connecting to a Projector on a Different Subnet 32 Connecting to a Projector on a Different Subnet This chapter explains how to connect a computer to a projector on a different sub-net via a Wired LAN or a wireless LAN access point on an existing network system. By default, this application only searches for projectors on the same subnet as the computer. Therefore, even if you perform a search for projectors on the network, projectors on a different subnet will not be found. You can, however, identify and connect to a projector on a different subnet as follows: • Specify either an IP address or Projector name and perform a search. The IP Address can be input directly. Also, provided the Projector name to be connected has been registered on the DNS server, you can perform a search simply by inputting that Projector name.s p.32 • Performing a search based on a Profile Once you have performed a search for a projector on a different subnet by specifying either an IP Address or a Projector name, you can save the search as a Profile with an easy-to-remember name, and then use that Profile whenever you subsequently want to search for a projector on a different subnet.s p.33 q • If a search fails to find a projector, the most likely causes are as follows. Proceed as appropriate, depending on the cause of the failure. For both Windows and Mac OS: If there is no wireless LAN signal or if the signal is weak, check whether there is anything that could be interfering with the signal. When the optional Wireless LAN unit is installed in the projector, and connecting Mac OS to a wireless LAN, check whether AirPort is set to On. Or, check whether an appropriate access point has been selected. • When you use Manual search in Quick Connection Mode, you can specify the SSID. When there are a lot of projectors you can narrow the search field by using SSID. Specifying Either an IP Address or Projector Name and Performing a Search (Advanced Connection Mode Only) In the following explanations, unless otherwise noted, Windows screen shots are used. Similar screens are also displayed for Mac OS. Procedure A Click "Manual search" on the EasyMP Network Projection projector selection screen.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
Connecting to a Projector on a Different Subnet
32
Connecting to a Projector on a Different Subnet
This chapter explains how to connect a computer to a projector on a
different sub-net via a Wired LAN or a wireless LAN access point on an
existing network system.
By default, this application only searches for projectors on the same
subnet as the computer. Therefore, even if you perform a search for
projectors on the network, projectors on a different subnet will not be
found.
You can, however, identify and connect to a projector on a different
subnet as follows:
•
Specify either an IP address or Projector name and perform a search.
The IP Address can be input directly. Also, provided the Projector
name to be connected has been registered on the DNS server, you can
perform a search simply by inputting that Projector name.
s
p.32
•
Performing a search based on a Profile
Once you have performed a search for a projector on a different subnet
by specifying either an IP Address or a Projector name, you can save
the search as a Profile with an easy-to-remember name, and then use
that Profile whenever you subsequently want to search for a projector
on a different subnet.
s
p.33
q
•
If a search fails to find a projector, the most likely causes are as follows.
Proceed as appropriate, depending on the cause of the failure.
For both Windows and Mac OS:
If there is no wireless LAN signal or if the signal is weak, check whether
there is anything that could be interfering with the signal.
When the optional Wireless LAN unit is installed in the projector, and
connecting Mac OS to a wireless LAN, check whether AirPort is set to On.
Or, check whether an appropriate access point has been selected.
•
When you use Manual search in Quick Connection Mode, you can specify
the SSID. When there are a lot of projectors you can narrow the search field
by using SSID.
Specifying Either an IP Address or Projector Name
and Performing a Search (Advanced Connection
Mode Only)
In the following explanations, unless otherwise noted, Windows screen
shots are used.
Similar screens are also displayed for Mac OS.
Procedure
A
Click "Manual search" on the EasyMP Network Projection
projector selection screen.