Gateway E-9220T Gateway E-9220T Server User Guide - Page 56

Replacing the processor

Get Gateway E-9220T PDF manuals and user guides View all Gateway E-9220T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Replacing the processor Replacing the processor The server is compatible with Intel® Celeron (533 MHz FSB), Pentium 4 (800 MHz FSB), and Pentium D (800 MHz FSB) processors with 256 KB (Celeron), 1 or 2 MB (Pentium 4), or 2×1 MB (Pentium D), L2 caches. The server automatically detects the processors each time you turn it on. Whenever you install new processors, you should first install the most current version of the BIOS. For more information, see "Updating the BIOS" on page 67. Warning Processors and heat sinks may be hot if the computer has been running. Also, there may be sharp edges on the heat sinks. Consider wearing protective gloves. Caution A heat sink must be installed on the processor. Installing a processor without a heat sink could damage the processor. To replace the processor: 1 Install the most current BIOS version. For more information, see "Updating the BIOS" on page 67. 2 Follow the instructions in "Preventing static electricity discharge" on page 29. 3 Follow the instructions in "Opening the server case" on page 30. 4 Follow the instructions in "Removing the processor air duct" on page 33. 5 Loosen the four captive heat sink screws (one on each corner). www.gateway.com 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
51
www.gateway.com
Replacing the processor
Replacing the processor
The server is compatible with Intel
®
Celeron (533 MHz FSB), Pentium 4 (800 MHz FSB),
and Pentium D (800 MHz FSB) processors with 256 KB (Celeron), 1 or 2 MB (Pentium 4),
or 2×1 MB (Pentium D), L2 caches. The server automatically detects the processors each
time you turn it on. Whenever you install new processors, you should first install the most
current version of the BIOS. For more information, see
“Updating the BIOS” on page 67
.
To replace the processor:
1
Install the most current BIOS version. For more information, see
“Updating the BIOS”
on page 67
.
2
Follow the instructions in
“Preventing static electricity discharge” on page 29
.
3
Follow the instructions in
“Opening the server case” on page 30
.
4
Follow the instructions in
“Removing the processor air duct” on page 33
.
5
Loosen the four captive heat sink screws (one on each corner).
Warning
Processors and heat sinks may be hot if the computer has been
running. Also, there may be sharp edges on the heat sinks. Consider
wearing protective gloves.
Caution
A heat sink must be installed on the processor. Installing a processor
without a heat sink could damage the processor.