Gateway GT5014H 8511124 - Gateway Canada mBTX Hardware Reference Guide - Page 21

Replacing the memory card reader

Get Gateway GT5014H PDF manuals and user guides View all Gateway GT5014H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

CHAPTER 3: Maintenance Basics www.gateway.com 4 Remove the two drive retention screws, then slide the drive forward and out of the drive bay. Drive retention screws 5 Note any jumper settings on the old drive and set the jumper on the new drive to be the same. 6 Slide the new drive into the drive bay, line up the screw holes on the drive bay with the screw holes on the drive, then replace the two drive retention screws. Drive retention screws 7 Reconnect the drive cables using your notes from Step 3. 8 Replace the front bezel by following the instructions in "Replacing the front bezel" on page 14. 9 Replace the side panel by following the instructions in "Replacing the side panel" on page 14. Replacing the memory card reader Tips & Tricks You need a Phillips screwdriver to replace the memory card reader. To replace the memory card reader: 1 Remove the side panel by following the instructions in "Removing the side panel" on page 12. 2 Remove the front bezel by following the instructions in "Removing the front bezel" on page 13. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
CHAPTER 3: Maintenance Basics
www.gateway.com
18
4
Remove the two drive retention screws, then slide the drive forward and
out of the drive bay.
5
Note any jumper settings on the old drive and set the jumper on the new
drive to be the same.
6
Slide the new drive into the drive bay, line up the screw holes on the drive
bay with the screw holes on the drive, then replace the two drive retention
screws.
7
Reconnect the drive cables using your notes from
Step 3
.
8
Replace the front bezel by following the instructions in
“Replacing the
front bezel” on page 14
.
9
Replace the side panel by following the instructions in
“Replacing the side
panel” on page 14
.
Replacing the memory card reader
Tips & Tricks
You need a Phillips screwdriver to replace
the memory card reader.
To replace the memory card reader:
1
Remove the side panel by following the instructions in
“Removing the side
panel” on page 12
.
2
Remove the front bezel by following the instructions in
“Removing the
front bezel” on page 13
.
Drive retention screws
Drive retention screws