Haier AB122MCERA Operation Manual - Page 19

Ab182-482meera

Get Haier AB122MCERA PDF manuals and user guides View all Haier AB122MCERA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Maintenance 3. Dismantle the air cleaner (as shown in Fig. 6). 4. Remove the air inlet grid (as shown in Fig. 7) Open the air inlet grid to 45 degree and lift it air cleaner Fig. 6 Put the white plastic protuberant,slightly drag it downwards to pull out the air cleaner Fig. 7 Cleaning Air Cleaner) • Cleaning Clean the air cleaner with the dust collector or water to remove dusts. For too much dust, use the fan or directly spray the special cookware detergent on the air inlet grid, and then clean it with water after 10 minutes. (A) remove dust with dust collector; (B) for too much dust, use soft-hair brush and mild detergent to clean. , _,_ (C) throw off water and then dry it at cool places. A Attention • Don't clean it with hot water of over 50t to avoid fading or distortion. • Don't dry it on the fire, or the cleaner might cause fire. Installing air cleaner and air inlet grid: • AB092-482MCERA 1. Mounting the gauze: opposite to the ways of dismantling the gauze (as shown in Fig. 3 above). 2. Mounting the air inlet grid: as shown in the right figure, nip the locks on the grid as directed by arrows, put the side with the lock device into the lock port, and then put the side with locks into the panel frame. Release the locks to position the grid after determining that the grid is abutting upon the bottom of the panel frame. locks lock device lock port \insert air in et grid • AB182-482MEERA 1. Set the air cleaner at the top of inlet grid. 2. Connect the two pullbacks for hoisting the grid to the air inlet grid (opposite to Step 2). • Mounting and closing the air inlet grid refer to Step 1. Connect the two pullbacks to the air inlet grid. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Maintenance
3.
Dismantle
the
air
cleaner
(as
shown
in
Fig.
6).
4.
Remove
the
air
inlet
grid
(as
shown
in
Fig.
7)
Open
the
air
inlet
grid
to
45
degree
and
lift
it
air
cleaner
Put
the white
plastic
protuberant,slightly
drag
it
downwards
to
pull
out
the
air
cleaner
Fig.
6
Fig.
7
Cleaning
Air
Cleaner)
•
Cleaning
Clean
the
air
cleaner
with
the
dust
collector
or
water
to
remove
dusts.
For
too
much
dust,
use
the
fan
or
directly
spray
the
special
cookware
detergent
on
the
air
inlet
grid,
and
then
clean
it
with
water
after
10
minutes.
(A)
remove
dust
with
dust
collector;
_,_
(B)
for
too
much
dust,
use
soft
-hair
brush
and
mild
detergent
to
clean.
,
(C)
throw
off
water
and
then
dry
it
at
cool
places.
A
Attention
•
Don't
clean
it
with
hot
water
of
over
50t
to
avoid
fading
or
distortion.
•
Don't
dry
it
on
the
fire,
or
the
cleaner
might
cause
fire.
Installing
air
cleaner
and
air
inlet
grid:
•
AB092-482MCERA
1.
Mounting
the
gauze:
opposite
to
the
ways
of
dismantling
the
gauze
(as
shown
in
Fig.
3
above).
2.
Mounting
the
air
inlet
grid:
as
shown
in
the
right
figure,
nip
the
locks
on
the
grid
as
directed
by
arrows,
put
the
side
with
the
lock
device
into
the
lock
port,
and
then
put
the
side
with
locks
into
the
panel
frame.
Release
the
locks
to
position
the
grid
after
determining
that
the
grid
is
abutting
upon
the
bottom
of
the
panel
frame.
locks
lock
device
lock
port
\insert
air
in
et
grid
•
AB182-482MEERA
1.
Set
the
air
cleaner
at
the
top
of
inlet
grid.
2.
Connect
the
two
pullbacks
for
hoisting
the
grid
to
the
air
inlet
grid
(opposite
to
Step
2).
•
Mounting
and
closing
the
air
inlet
grid
refer
to
Step
1.
Connect
the
two
pullbacks
to
the
air
inlet
grid.
17