Haier AB122MCERA Operation Manual - Page 26

deflector, swing, orifice, location

Get Haier AB122MCERA PDF manuals and user guides View all Haier AB122MCERA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Installation Procedures 0 AB182-482MEERA ED As shown in Fig. 1, make the wind deflector motor of the decorated board face to the orifice of the indoor unit, and then mount the decorated board onto the body of the indoor unit. swing ring T orifice location deflector moto 4 Fig.1 o Mounting the decorated board: a. Hang temporarily the two swing rings opposite to the deflector motor of the decorated board on the ring stators of the swing rings of the indoor unit; b. Hang temporarily the other two swing rings on the ring stators of the swing rings of the indoor unit (take care not to get the lead wire of the deflector motor into the sealing); c. Screw all 4 hex head screws under the rings about 15mm to lift the board; d. Turn and adjust the decorated board in the direction of arrow as shown in Fig. 4 until it covers the hole of the ceiling. e. Fasten the screw to keep the thickness of the sealing between the decorated board and the unit body within 5-8mm, as shown in Fig. 2. indoor unit sealing ceiling material \ t 5-8mm decorated board Fig.2 f. Mount the wiring of the decorated board according to the mounting drawing attached to the inside of the machine; g. Check with the controller if the mounting is correct and make sure if the machine works normally; h. Mount the air inlet grid and corner covers. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Installation
Procedures
0
AB182-482MEERA
ED
As
shown
in
Fig.
1,
make
the
wind
deflector
motor
of
the
decorated
board
face
to
the
orifice
of
the
indoor
unit,
and
then
mount
the
decorated
board
onto
the
body
of
the
indoor
unit.
deflector
moto
4
swing
ring
orifice
location
T
Fig.1
o
Mounting
the
decorated
board:
a.
Hang
temporarily
the
two
swing
rings
opposite
to
the
deflector
motor
of
the
decorated
board
on
the
ring
stators
of
the
swing
rings
of
the
indoor
unit;
b.
Hang
temporarily
the
other
two
swing
rings
on
the
ring
stators
of
the
swing
rings
of
the
indoor
unit
(take
care
not
to
get
the
lead
wire
of
the
deflector
motor
into
the
sealing);
c.
Screw
all
4
hex
head
screws
under
the
rings
about
15mm
to
lift
the
board;
d.
Turn
and
adjust
the
decorated
board
in
the
direction
of
arrow
as
shown
in
Fig.
4
until
it
covers
the
hole
of
the
ceiling.
e.
Fasten
the
screw
to
keep
the
thickness
of
the
sealing
between
the
decorated
board
and
the
unit
body
within
5-8mm,
as
shown
in
Fig.
2.
indoor
unit
sealing
ceiling
material
\
t
5-8mm
decorated
board
Fig.2
f.
Mount
the
wiring
of
the
decorated
board
according
to
the
mounting
drawing
attached
to
the
inside
of
the
machine;
g.
Check
with
the
controller
if
the mounting
is
correct
and
make
sure
if
the
machine
works
normally;
h.
Mount
the
air
inlet
grid
and
corner
covers.
24