HP 12000 HP 12200 Gateway Virtual Library System User Guide (BW403-10001, June - Page 63

Viewing the Replication Target Slot Details

Get HP 12000 PDF manuals and user guides View all HP 12000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

NOTE: When you configure a virtual library as a LAN/WAN replication target with Echo Copy, you may also need to hide it (e.g., using LUN masking or port mapping/zoning) from the front-end SAN in the case where the same backup application instance sees both the source and destination VLS devices. (The backup application must not see the same tape barcode in two places at the same time.) See "LUN Mapping" (page 91) for details. Viewing the Replication Target Slot Details On the navigation tree, select Slots from the expanded replication target list to view the replication target slots. The screen displays the barcode and last successful echo copy for each slot. The last successful echo copy is intended to notify you of problems with the echo copy, but is not necessarily related to the Cartridge Status or Last Mirrored fields on the Summary for Slots or Summary for Cartridges screens. The state can be "unknown" when only the header transferred to the tape, when nothing transferred to the tape, during the transfer of data, or when a data transfer has failed. Setting the Global LAN/WAN Replication Target Configuration 1. Click the Automigration/Replication tab. 2. In the navigation tree, expand Configuration Summary. 3. Select Global LAN/WAN Target Configuration. 4. From the Default Compression Setting for LAN/WAN Replication Targets menu, select whether the compression for LAN/WAN replication targets is on (Yes) or off (No) by default. If your network has a WAN accelerator that performs compression installed between the source VLS and the target VLS, setting this to No will usually speed up data transfers during replication. 5. Enter a new port number for unencrypted data transfer only if you need to change it from the default. Your firewall may require that the data transfer use a different port number. 6. Click Submit. Editing a LAN/WAN Replication Target To edit the LAN/WAN replication target settings: 1. Select the Automigration/Replication tab. 2. Expand LAN/WAN Replication Targets on the navigation tree, and then select the target of interest. The LAN/WAN Replication Target Details screen displays. 3. Select Edit from the task bar. 4. On the Edit LAN/WAN Replication Target Settings screen, edit the target settings as needed. For an explanation of the settings, see Creating a LAN/WAN Replication Target. 5. Select Submit. To edit the slot mapping, see "Changing the Slot Mapping for a LAN/WAN Library" (page 49). To edit the availability window: 1. Follow steps 1 through 3 above. 2. Select Edit Availability Windows from the task bar to open that screen. The Edit Availability Windows screen displays. 3. To delete a availability window, select Delete in the row of that policy window in the Current Availability Windows section of the screen. 4. To add a availability window, enter the information in the Add Availability Window section of the screen, and then select Add. Repeat this step for as many availability windows as you need. LAN/WAN Replication Target Operations 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
NOTE:
When you configure a virtual library as a LAN/WAN replication target with Echo Copy,
you may also need to hide it (e.g., using LUN masking or port mapping/zoning) from the front-end
SAN in the case where the same backup application instance sees both the source and destination
VLS devices. (The backup application must not see the same tape barcode in two places at the
same time.) See
“LUN Mapping” (page 91)
for details.
Viewing the Replication Target Slot Details
On the navigation tree, select
Slots
from the expanded replication target list to view the replication
target slots. The screen displays the barcode and last successful echo copy for each slot.
The last successful echo copy is intended to notify you of problems with the echo copy, but is not
necessarily related to the Cartridge Status or Last Mirrored fields on the Summary for Slots or
Summary for Cartridges screens. The state can be “unknown” when only the header transferred
to the tape, when nothing transferred to the tape, during the transfer of data, or when a data
transfer has failed.
Setting the Global LAN/WAN Replication Target Configuration
1.
Click the
Automigration/Replication
tab.
2.
In the navigation tree, expand
Configuration Summary
.
3.
Select
Global LAN/WAN Target Configuration
.
4.
From the
Default Compression Setting for LAN/WAN Replication Targets
menu, select whether
the compression for LAN/WAN replication targets is on (Yes) or off (No) by default.
If your network has a WAN accelerator that performs compression installed between the
source VLS and the target VLS, setting this to No will usually speed up data transfers during
replication.
5.
Enter a new port number for unencrypted data transfer
only
if you need to change it from the
default.
Your firewall may require that the data transfer use a different port number.
6.
Click
Submit
.
Editing a LAN/WAN Replication Target
To edit the LAN/WAN replication target settings:
1.
Select the
Automigration/Replication
tab.
2.
Expand
LAN/WAN Replication Targets
on the navigation tree, and then select the target of
interest. The
LAN/WAN Replication Target Details
screen displays.
3.
Select
Edit
from the task bar.
4.
On the
Edit LAN/WAN Replication Target Settings
screen, edit the target settings as needed.
For an explanation of the settings, see
Creating a LAN/WAN Replication Target
.
5.
Select
Submit
.
To edit the slot mapping, see
“Changing the Slot Mapping for a LAN/WAN Library” (page 49)
.
To edit the availability window:
1.
Follow steps 1 through 3 above.
2.
Select
Edit Availability Windows
from the task bar to open that screen.
The
Edit Availability Windows
screen displays.
3.
To delete a availability window, select
Delete
in the row of that policy window in the
Current
Availability Windows
section of the screen.
4.
To add a availability window, enter the information in the
Add Availability Window
section
of the screen, and then select
Add
.
Repeat this step for as many availability windows as you need.
LAN/WAN Replication Target Operations
63