HP 4400 HP StorageWorks Fabric OS 6.4.0c Release Notes (5697-0703, September 2 - Page 58

Performance Monitoring on Port Throughput and Port Error setup win

Get HP 4400 PDF manuals and user guides View all HP 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Closed defect summary Solution Software verify error detected appears on console during upgrade to Fixed in Fabric OS 6.4.0 6.3.0 from RC builds on HP StorageWorks 8/80 SAN Switch. This issue will not be seen in the field. Display of the CP disappeared from WebTools when the blade experi- Fixed in Fabric OS 6.4.0 enced a fault. WebTools message of "Maximum length reached for your input" in Performance Monitoring on Port Throughput and Port Error setup window. Fixed in Fabric OS 6.4.0 CALD panic occurred on a director and CPs got out of sync, but no failover happened as CALD was in defunct state due to race condition. Fixed in Fabric OS 6.4.0 Workaround prior to upgrade: Manually reboot. Retransmit and Out of order counters displayed in the portshow fciptun- Fixed in Fabric OS 6.4.0 nel output do not show correct values. 400 Multiprotocol router or multiprotocol router blade non-distruptive firmware upgrade from 6.2.0g to 6.3.0 causes the switch to go Faulty 21. Fixed in Fabric OS 6.4.0 With 1606 Extension SAN Switch or Multiprotocol Extension Blade, Fixed in Fabric OS 6.4.0 FCIP configuration cannot be restored to default setting by using configdefault, even after chassis reboot. Circuit-0 shows InProg after changing 10G tunnel to compression enable in repeated manner during stress to fail testing. Fixed in Fabric OS 6.4.0 Workaround prior to upgrade: Use slotpower off followed by slotpower on usually clears this problem. Interface flapping/ bad cable shows to many ras log messages Fixed in Fabric OS 6.4.0 Workaround prior to upgrade: Shut down the port and replace the faulty cable and enable the port. Telnet banner and switchname are not consistent after a new switchname is defined without doing multiple hafailover commands. Can also occur after a standby CP is replaced where the new CP hosts file does not get synchronized with active CP without two hafailover commands. Fixed in Fabric OS 6.4.0 Workaround prior to upgrade: Use the "hostname xyz" command when a "switchname xyz" is used. Also, this issue does not occur with SSH as it does not use the banner. In a rare occurrence, HA synchronization is lost after a switch with trunk ports panics and manual reboot was needed to recover, due to race condition with trunk ports dropping Exchange Fabric Parameter (EFP) response. Fixed in Fabric OS 6.4.0 On HP StorageWorks DC SAN or DC04 director, SwFCPortTxType MIB Fixed in Fabric OS 6.4.0 does not report the type of CoreBlade's ICL port correctly. Reports as swFCPortTxType.385 unknown(1). Byte Streaming support on 400 multiprotocol router/multiprotocol router Fixed in Fabric OS 6.4.0 blade does not work with 3rd party optimizers. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Solution
Closed defect summary
Fixed in Fabric OS 6.4.0
Software verify error detected appears on console during upgrade to
6.3.0 from RC builds on HP StorageWorks 8/80 SAN Switch. This issue
will not be seen in the field.
Fixed in Fabric OS 6.4.0
Display of the CP disappeared from WebTools when the blade experi-
enced a fault.
Fixed in Fabric OS 6.4.0
WebTools message of "Maximum length reached for your input" in
Performance Monitoring on Port Throughput and Port Error setup win-
dow.
Fixed in Fabric OS 6.4.0
Workaround prior to upgrade:
Manually reboot.
CALD panic occurred on a director and CPs got out of sync, but no
failover happened as CALD was in defunct state due to race condition.
Fixed in Fabric OS 6.4.0
Retransmit and Out of order counters displayed in the portshow fciptun-
nel output do not show correct values.
Fixed in Fabric OS 6.4.0
400 Multiprotocol router or multiprotocol router blade non-distruptive
firmware upgrade from 6.2.0g to 6.3.0 causes the switch to go Faulty
21.
Fixed in Fabric OS 6.4.0
With 1606 Extension SAN Switch or Multiprotocol Extension Blade,
FCIP configuration cannot be restored to default setting by using config-
default, even after chassis reboot.
Fixed in Fabric OS 6.4.0
Workaround prior to upgrade:
Use slotpower off followed by
slotpower on usually clears this
problem.
Circuit-0 shows InProg after changing 10G tunnel to compression enable
in repeated manner during stress to fail testing.
Fixed in Fabric OS 6.4.0
Workaround prior to upgrade:
Shut down the port and replace the
faulty cable and enable the port.
Interface flapping/ bad cable shows to many ras log messages
Fixed in Fabric OS 6.4.0
Workaround prior to upgrade:
Use the "hostname xyz" command
when a "switchname xyz" is used.
Also, this issue does not occur with
SSH as it does not use the banner.
Telnet banner and switchname are not consistent after a new switchname
is defined without doing multiple hafailover commands. Can also occur
after a standby CP is replaced where the new CP hosts file does not
get synchronized with active CP without two hafailover commands.
Fixed in Fabric OS 6.4.0
In a rare occurrence, HA synchronization is lost after a switch with trunk
ports panics and manual reboot was needed to recover, due to race
condition with trunk ports dropping Exchange Fabric Parameter (EFP)
response.
Fixed in Fabric OS 6.4.0
On HP StorageWorks DC SAN or DC04 director, SwFCPortTxType MIB
does not report the type of CoreBlade's ICL port correctly. Reports as
swFCPortTxType.385 unknown(1).
Fixed in Fabric OS 6.4.0
Byte Streaming support on 400 multiprotocol router/multiprotocol router
blade does not work with 3rd party optimizers.
58