HP 4400 HP StorageWorks Fabric OS 6.4.0c Release Notes (5697-0703, September 2 - Page 64

Unable to ReCreate Frame Redirect Zone After Disabling McDATA De

Get HP 4400 PDF manuals and user guides View all HP 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Closed defect summary Solution Configdownload is successful with invalid SNMP v1/v3 trap recipients. Fixed in Fabric OS 6.4.0 In a large fabric with 50+ switches, observed errors: 'queue ns: queue Fixed in Fabric OS 6.4.0 full (miss=1)' when enabling the config file 'cfgenable'. In 1606 extension SAN switch, Licenseremove command gets executed Fixed in Fabric OS 6.4.0 for slot based license, which configured to blade slot. supportsave failed error message for nonexistent blade may be seen on DC SAN Backbone director after multiprotocol router blade is hot swapped with multiprotocol extension blade. Fixed in Fabric OS 6.4.0 Switch responds with advertisement to solicitation with SP bit on. Fixed in Fabric OS 6.4.0 Unable to ReCreate Frame Redirect Zone After Disabling McDATA De- Fixed in Fabric OS 6.4.0 fault Zone. Switch stuck in 'merge in progress' even though there's no transaction. FCoE Login management operations can't be performed, unless the switch is disabled, until then FCoE Fabric Merge is struck. Fixed in Fabric OS 6.4.0 Workaround prior to upgrade: Workaround to come out of the deadlock: 1. Break the fabric by bringing down the ISL. 2. Both switches will merge and generation number will be rectified (made consistent) with configuration. 3. Bring the ISL back up and merge will go through. Or 1. Do a switchdisable on non-lowest domain switch (without touching other switches or ISL) 2. Do fcoelogincfg -disable 3. switchenable 4. fcoelogincfg -enable and create required login groups. Resources are incorrectly shown to be available for TopTalker fabmode when the max are already used in other FIDs. Fixed in Fabric OS 6.4.0 Workaround prior to upgrade: Execute "perfresourceshow --fabmodeRes" on all logical partitions. The SNMP queries for the port speeds of FCoE ports actually return 0 Fixed in Fabric OS 6.4.0 GB/sec. You may see bmd assert and failover if the multiprotocol router blade is plugged in and plugged out too quickly. BMD assert caused DC04 SAN director CP to failover. Fixed in Fabric OS 6.4.0 [Stress to Fail Test] Running "chassisdisable; chassisenable, followed by hafailover" continuously may result in VERIFY messages. Fixed in Fabric OS 6.4.0 Web Tools is not allowing user to set and modify switch name with "."but CLI allows the same in FMS and non-FMS mode. Fixed in Fabric OS 6.4.0 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Solution
Closed defect summary
Fixed in Fabric OS 6.4.0
Configdownload is successful with invalid SNMP v1/v3 trap recipients.
Fixed in Fabric OS 6.4.0
In a large fabric with 50+ switches, observed errors: 'queue ns: queue
full (miss=1)' when enabling the config file 'cfgenable'.
Fixed in Fabric OS 6.4.0
In 1606 extension SAN switch, Licenseremove command gets executed
for slot based license, which configured to blade slot.
Fixed in Fabric OS 6.4.0
supportsave failed error message for nonexistent blade may be seen
on DC SAN Backbone director after multiprotocol router blade is hot
swapped with multiprotocol extension blade.
Fixed in Fabric OS 6.4.0
Switch responds with advertisement to solicitation with SP bit on.
Fixed in Fabric OS 6.4.0
Unable to ReCreate Frame Redirect Zone After Disabling McDATA De-
fault Zone.
Fixed in Fabric OS 6.4.0
Workaround prior to upgrade:
Workaround to come out of the
deadlock:
1. Break the fabric by bringing down
the ISL.
2. Both switches will merge and
generation number will be rectified
(made consistent) with configuration.
3. Bring the ISL back up and merge
will go through.
Or
1. Do a switchdisable on non-lowest
domain switch (without touching
other switches or ISL)
2. Do fcoelogincfg
–
disable
3. switchenable
4. fcoelogincfg
–
enable and create
required login groups.
Switch stuck in 'merge in progress' even though there's no transaction.
FCoE Login management operations can't be performed, unless the
switch is disabled, until then FCoE Fabric Merge is struck.
Fixed in Fabric OS 6.4.0
Workaround prior to upgrade:
Execute "perfresourceshow
--fabmodeRes" on all logical
partitions.
Resources are incorrectly shown to be available for TopTalker fabmode
when the max are already used in other FIDs.
Fixed in Fabric OS 6.4.0
The SNMP queries for the port speeds of FCoE ports actually return 0
GB/sec.
Fixed in Fabric OS 6.4.0
You may see bmd assert and failover if the multiprotocol router blade
is plugged in and plugged out too quickly. BMD assert caused DC04
SAN director CP to failover.
Fixed in Fabric OS 6.4.0
[Stress to Fail Test] Running "chassisdisable; chassisenable, followed
by hafailover" continuously may result in VERIFY messages.
Fixed in Fabric OS 6.4.0
Web Tools is not allowing user to set and modify switch name with
"."but CLI allows the same in FMS and non-FMS mode.
64