HP Cisco MDS 9020 Cisco MDS 9100 Series Hardware Installation Guide (OL-17951- - Page 57

Installing Power Supplies, Cisco MDS 9100 Series AC Power Supply

Get HP Cisco MDS 9020 - Fabric Switch PDF manuals and user guides View all HP Cisco MDS 9020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Chapter 2 Installing the Cisco MDS 9100 Series Removing and Installing Components Send documentation comments to [email protected] Figure 2-23 Cisco MDS 9100 Series AC Power Supply 94008 AC OK DC OK Installing Power Supplies To install the dual 300-W AC-input power supplies, follow these steps: Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Ensure that the system (earth) ground connection has been made. Make sure the power cord is disconnected before installing the power supply. Verify that the power switch is in the off (0) position on the power supply that you are installing. Slide the power supply into the power supply bay. Make sure that the power supply is fully seated in the bay. Tighten the power supply captive screw. Plug the power cord into the power supply. Connect the other end of the power cord to an AC-input power source. Note Depending on the outlet receptacle on your power distribution unit, you may need the optional jumper power cord to connect the Cisco MDS 9100 Series switch to your outlet receptacle. See the "Jumper Power Cord" section on page C-5. Step 8 Step 9 Turn the power switch to the on (|) position on the power supply. Verify power supply operation by checking that the power supply (P/S) LED in the front panel is green. If the LED is not green, see the Cisco MDS 9000 Family Troubleshooting Guide. OL-17951-02 Cisco MDS 9100 Series Hardware Installation Guide 2-29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Send documentation comments to [email protected]
2-29
Cisco MDS 9100 Series Hardware Installation Guide
OL-17951-02
Chapter 2
Installing the Cisco MDS 9100 Series
Removing and Installing Components
Figure 2-23
Cisco MDS 9100 Series AC Power Supply
Installing Power Supplies
To install the dual 300-W AC-input power supplies, follow these steps:
Step 1
Ensure that the system (earth) ground connection has been made.
Step 2
Make sure the power cord is disconnected before installing the power supply.
Step 3
Verify that the power switch is in the off (0) position on the power supply that you are installing.
Step 4
Slide the power supply into the power supply bay. Make sure that the power supply is fully seated in the
bay.
Step 5
Tighten the power supply captive screw.
Step 6
Plug the power cord into the power supply.
Step 7
Connect the other end of the power cord to an AC-input power source.
Note
Depending on the outlet receptacle on your power distribution unit, you may need the optional
jumper power cord to connect the Cisco MDS 9100 Series switch to your outlet receptacle. See
the
“Jumper Power Cord” section on page C-5
.
Step 8
Turn the power switch to the on (|) position on the power supply.
Step 9
Verify power supply operation by checking that the power supply (P/S) LED in the front panel is green.
If the LED is not green, see the
Cisco MDS 9000 Family Troubleshooting Guide
.
94008
DC OK
AC OK