Home » HP Manuals » Storage Devices » HP Cisco MDS 9020 » Manual Viewer

HP Cisco MDS 9020 Cisco MDS 9100 Series Hardware Installation Guide (OL-17951- - Page 92

Optical Specifications for Cisco CWDM SFP Transceivers, Parameter, Symbol, Minimum, Typical, Units

Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

SFP Transceiver Specifications Appendix B Technical Specifications Send documentation comments to [email protected] Table B-19 Electrical Specifications for Cisco CWDM SFP Transceivers Parameter Supply Current Surge Current Input voltage Symbol |s |surge Vmax Minimum 3.1 Typical 220 3.3 Maximum 300 +30 3.6 Units mA mA V Optical Specifications for Cisco CWDM SFP Transceivers Table B-20 provides the optical specifications for CWDM SFP transceivers. CWDM SFP transceivers have an optical link budget of 28 decibels (db). Note The parameters are specified over temperature and at end of life unless otherwise noted. Note When shorter distances of single-mode fiber are used, it might be necessary to insert an inline optical attenuator in the link to avoid overloading the receiver. Table B-20 Optical Specifications for Cisco CWDM SFP Transceivers Parameter Symbol Min. Transmitter central λc wavelength (x-4) Wavelength temperature dependence Side-mode SMSR 30 suppression ratio Transmitter optical Pout 0.0 output power Receiver optical input power (BER

Section	Page
Cisco MDS 9100 Series Hardware Installation Guide	1
Contents	3
New and Changed Information	7
Preface	9
Audience	9
Organization	9
Document Conventions	10
Related Documentation	12
Release Notes	12
Compatibility Information	12
Regulatory Compliance and Safety Information	12
Hardware Installation	12
Cisco Fabric Manager	13
Command-Line Interface	13
Intelligent Storage Networking Services Configuration Guides	13
Troubleshooting and Reference	13
Installation and Configuration Note	13
Obtaining Documentation, Obtaining Support, and Security Guidelines	14
Product Overview	15
Cisco MDS 9100 Series Multilayer Fabric Switches	16
Cisco MDS 9134 Switch	17
Cisco MDS 9124 Switch	18
Cisco MDS 9140 Switch	18
Cisco MDS 9120 Switch	19
Cisco MDS Fibre Channel Bladeswitch for IBM BladeCenter	19
Power Supplies	20
Fan Modules	20
Cisco MDS 9100 Series Ports	21
Ports on the Cisco MDS 9134 Switch	21
Ports on the Cisco MDS 9124 Switch	23
Ports on the Cisco MDS 9140 Switch and the Cisco MDS 9120 Switch	23
Switch LEDs	24
Supported SFP Transceivers	27
Fibre Channel SFP Transceivers	27
Combination Fibre Channel/Gigabit Ethernet SFP Transceivers	28
CWDM Combination Fibre Channel/Gigabit Ethernet SFP Transceivers	28
Installing the Cisco MDS 9100 Series	29
Preinstallation	30
Installation Options	30
Installation Guidelines	31
Required Equipment	32
Unpacking and Inspecting the Switch	32
Installing the Switch in a Cabinet or Rack	33
Front-Facing Installation	34
Installing the Switch in a Cabinet with Insufficient Front Clearance	39
Installing Front Rack-Mount Brackets for Cabinets with 26 Inches or Greater of Rail Spacings	41
Installing Front Rack-Mount Brackets for Cabinets with Less Than 26 Inches of Rail Spacings	42
Installing Cisco MDS 9100 Series Switch Rear-Facing into Cabinet	43
Installing a Cisco MDS 9134 Switch or a Cisco MDS 9124 Switch Rear-Facing into Cabinet	45
Installing Cisco MDS 9134 48-Port and 64-Port Stackable Bundles	49
Grounding the Switch	51
Starting Up the Switch	52
Removing and Installing Components	54
Removing and Installing AC Power Supplies	56
Removing Power Supplies	56
Installing Power Supplies	57
Removing and Installing DC Power Supplies	58
Removing Power Supplies	58
Installing Power Supplies	59
Removing and Installing Fan Modules	60
Removing a Fan Module on the Cisco MDS 9140 Switch, the Cisco MDS 9120 Switch, and the Cisco MDS 9134 Switch	60
Installing a Fan Module	61
Verifying the Fan Module	62
Connecting the Cisco MDS 9100 Series	63
Preparing for Network Connections	63
Connecting the Console Port	63
Connecting the Console Port to a PC	64
Connecting a Modem to a Console Port	65
Connecting the 10/100 Ethernet Management Port	65
Connecting to a Fibre Channel Port	66
Removing and Installing SFP Transceivers	66
Installing an SFP Transceiver	67
Removing an SFP Transceiver	68
Removing and Installing Cables into SFP Transceivers	69
Installing a Cable into an SFP Transceiver	69
Removing a Cable from an SFP Transceiver	70
Maintaining SFP Transceivers and Fiber-Optic Cables	71
Cabinet and Rack Installation	73
Cabinet and Rack Requirements	73
General Requirements for Cabinets and Racks	73
Requirements Specific to Perforated Cabinets	74
Reference Perforated Cabinet	74
Requirements Specific to Solid-Walled Cabinets	75
Requirements Specific to Standard Open Racks	75
Requirements Specific to Telco Racks	75
Cisco MDS 9000 Family Telco and EIA Shelf Bracket	75
Rack-Mounting Guidelines	76
Before Installing the Shelf Brackets	77
Required Equipment	77
Installing the Shelf Bracket Kit into a Two-Post Telco Rack	77
Installing the Shelf Bracket Kit into a Four-Post EIA Rack	79
Installing the Switch on the Shelf Brackets	80
Removing the Shelf Bracket Kit (Optional)	81
Technical Specifications	83
Switch Specifications	83
Power Specifications	84
General Power Supply Specifications	85
Power Supply Requirements and Heat Dissipation Specifications	85
Connection Guidelines for AC-Powered Systems	87
SFP Transceiver Specifications	87
Cisco Fibre Channel SFP Transceivers	87
General Specifications for Cisco Fibre Channel SFP Transceivers	88
Environmental and Electrical Specifications for Cisco Fibre Channel SFP Transceivers	89
Cisco Gigabit Ethernet/Fibre Channel Transceivers	89
General Specifications for Cisco GE/FC SFP Transceivers	89
Environmental and Electrical Specifications for Cisco GE/FC SFP Transceivers	90
Cisco CWDM SFP Transceivers	90
General Specifications for Cisco CWDM SFP Transceivers	91
Environmental and Electrical Specifications for Cisco CWDM SFP Transceivers	91
Optical Specifications for Cisco CWDM SFP Transceivers	92
X2 Transceiver Specifications	93
Cable and Port Specifications	95
Cables and Adapters	95
Console Port	96
Console Port Pinouts	96
Connecting the Console Port to a Computer Using the DB-25 Adapter	96
Connecting the Console Port to a Computer Using the DB-9 Adapter	97
MGMT 10/100 Ethernet Port	97
Supported Power Cords and Plugs	98
Power Cords	98
Jumper Power Cord	99
Site Planning and Maintenance Records	101
Site Preparation Checklist	101
Contact and Site Information	103
Chassis and Network Information	104

Match case Limit results 1 per page

Send documentation comments to [email protected]

B-10

Cisco MDS 9100 Series Hardware Installation Guide

OL-17951-02

Appendix B

Technical Specifications

SFP Transceiver Specifications

Optical Specifications for Cisco CWDM SFP Transceivers

Table B-20

provides the optical specifications for CWDM SFP transceivers. CWDM SFP transceivers

have an optical link budget of 28 decibels (db).

Note

The parameters are specified over temperature and at end of life unless otherwise noted.

Note

When shorter distances of single-mode fiber are used, it might be necessary to insert an inline optical

attenuator in the link to avoid overloading the receiver.

Table B-19

Electrical Specifications for Cisco CWDM SFP Transceivers

Parameter

Symbol

Minimum

Typical

Maximum

Units

Supply Current

220

300

Surge Current

surge

+30

Input voltage

Vmax

3.1

3.3

3.6

Table B-20

Optical Specifications for Cisco CWDM SFP Transceivers

Parameter

Symbol

Min.

Typical

Max.

Units

Notes

Transmitter central

wavelength

(x-4)

(x+1)

(x+7)

Available

center

wavelengths:

1470, 1490,

1510, 1530,

1550, 1570,

1590, 1610 nm

Wavelength

temperature

dependence

0.08

0.1

nm/°

Side-mode

suppression ratio

SMSR

Transmitter optical

output power

out

0.0

5.0

dBm

Average power

coupled into

single-mode

fiber

Receiver optical

input power (BER

<10

-12

with PRBS

-7

–1)

-28.0

-7.0

dBm

@ 2.12 Gbps,

140°F (60°C)

case temp.

Receiver optical

input wavelength

1450

1620

Transmitter

extinction ratio

OMI