HP Cisco MDS 9020 Cisco MDS 9100 Series Hardware Installation Guide (OL-17951- - Page 79

Installing the Shelf Bracket Kit into a Four-Post EIA Rack, A-2

Get HP Cisco MDS 9020 - Fabric Switch PDF manuals and user guides View all HP Cisco MDS 9020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Appendix A Cabinet and Rack Installation Cisco MDS 9000 Family Telco and EIA Shelf Bracket Send documentation comments to [email protected] Installing the Shelf Bracket Kit into a Four-Post EIA Rack Figure A-2 shows the installation of the shelf bracket kit into a four-post EIA rack. Figure A-2 Installing the Shelf Bracket Kit into an EIA Rack 1 2 3 4 5 105087 1 Rack-mounting rail (4x) 2 Shelf bracket (2x) 3 Slider rail (2) 4 Crossbar 5 10-32 screws (2x) To install the shelf brackets in an EIA rack, follow these steps: Step 1 Position a shelf bracket inside the rack-mounting rails as shown in Figure A-2. Align the screw holes at the front of the shelf bracket with the holes in the front rack-mounting rail. Then attach the shelf bracket to the front rack-mounting rail using a minimum of four 12-24 or 10-24 screws. Note The bottom hole of the shelf bracket should align with the bottom hole of a rack unit on the rack-mounting rail (the hole immediately above the 1/2-in. spacing). Step 2 Repeat with the other shelf bracket. Step 3 Verify that the shelf brackets are at the same height (using the level or tape measure as desired). OL-17951-02 Cisco MDS 9100 Series Hardware Installation Guide A-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Send documentation comments to [email protected]
A-7
Cisco MDS 9100 Series Hardware Installation Guide
OL-17951-02
Appendix A
Cabinet and Rack Installation
Cisco MDS 9000 Family Telco and EIA Shelf Bracket
Installing the Shelf Bracket Kit into a Four-Post EIA Rack
Figure A-2
shows the installation of the shelf bracket kit into a four-post EIA rack.
Figure A-2
Installing the Shelf Bracket Kit into an EIA Rack
To install the shelf brackets in an EIA rack, follow these steps:
Step 1
Position a shelf bracket inside the rack-mounting rails as shown in
Figure A-2
. Align the screw holes at
the front of the shelf bracket with the holes in the front rack-mounting rail. Then attach the shelf bracket
to the front rack-mounting rail using a minimum of four 12-24 or 10-24 screws.
Note
The bottom hole of the shelf bracket should align with the bottom hole of a rack unit on the
rack-mounting rail (the hole immediately above the 1/2-in. spacing).
Step 2
Repeat with the other shelf bracket.
Step 3
Verify that the shelf brackets are at the same height (using the level or tape measure as desired).
1
Rack-mounting rail (4x)
4
Crossbar
2
Shelf bracket (2x)
5
10-32 screws (2x)
3
Slider rail (2)
1
2
3
5
4
105087