HP Cisco MDS 9020 Cisco MDS 9100 Series Hardware Installation Guide (OL-17951- - Page 95

Cable and Port Specifications, Cables and Adapters

Get HP Cisco MDS 9020 - Fabric Switch PDF manuals and user guides View all HP Cisco MDS 9020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Send documentation comments to [email protected] C A P P E N D I X Cable and Port Specifications This appendix includes the cables and connectors used with the Cisco MDS 9100 Series Fixed Configuration Fabric Switch, and it includes the following sections: • Cables and Adapters, page C-1 • Console Port, page C-2 • MGMT 10/100 Ethernet Port, page C-3 • Supported Power Cords and Plugs, page C-4 Caution We strongly recommend that power cable runs and other potential noise sources be located as far away as practical from network cabling that terminates on Cisco equipment. In situations where long parallel cable runs exist but cannot be separated by at least 3.3 ft. (1 m), we recommend that you shield these potential noise sources. To avoid interference, the source should be shielded by housing it in a grounded metallic conduit. Cables and Adapters The Cisco MDS 9100 Series accessory kit includes the following: • RJ-45 to RJ-45 rollover cable • RJ-45 to DB-9 female DTE adapter (labeled "Terminal") • RJ-45 to DB-25 female DTE adapter (labeled "Terminal") • RJ-45 to DB-25 male DCE adapter (labeled "Modem") Note Additional cables and adapters can be ordered from your customer service representative. Note If you purchased this product through a Cisco reseller, contact the reseller directly for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL: http://www.cisco.com/techsupport. OL-17951-02 Cisco MDS 9100 Series Hardware Installation Guide C-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Send documentation comments to [email protected]
C-1
Cisco MDS 9100 Series Hardware Installation Guide
OL-17951-02
APPENDIX
C
Cable and Port Specifications
This appendix includes the cables and connectors used with the Cisco MDS 9100 Series Fixed
Configuration Fabric Switch, and it includes the following sections:
•
Cables and Adapters, page C-1
•
Console Port, page C-2
•
MGMT 10/100 Ethernet Port, page C-3
•
Supported Power Cords and Plugs, page C-4
Caution
We strongly recommend that power cable runs and other potential noise sources be located as far away
as practical from network cabling that terminates on Cisco equipment. In situations where long parallel
cable runs exist but cannot be separated by at least 3.3 ft. (1 m), we recommend that you shield these
potential noise sources. To avoid interference, the source should be shielded by housing it in a grounded
metallic conduit.
Cables and Adapters
The Cisco MDS 9100 Series accessory kit includes the following:
•
RJ-45 to RJ-45 rollover cable
•
RJ-45 to DB-9 female DTE adapter (labeled “Terminal”)
•
RJ-45 to DB-25 female DTE adapter (labeled “Terminal”)
•
RJ-45 to DB-25 male DCE adapter (labeled “Modem”)
Note
Additional cables and adapters can be ordered from your customer service representative.
Note
If you purchased this product through a Cisco reseller, contact the reseller directly for technical support.
If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL:
.