HP Cisco MDS 9020 Cisco MDS 9100 Series Hardware Installation Guide (OL-17951- - Page 78

A-1, Step 1

Get HP Cisco MDS 9020 - Fabric Switch PDF manuals and user guides View all HP Cisco MDS 9020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Cisco MDS 9000 Family Telco and EIA Shelf Bracket Appendix A Cabinet and Rack Installation Send documentation comments to [email protected] To install the shelf brackets in a telco rack, follow these steps: Step 1 Position a shelf bracket inside a rack-mounting rail as shown in Figure A-1 and align the screw holes at the front of the shelf bracket with the holes in the rack-mounting rail. Then attach the shelf bracket to the rack-mounting rail using a minimum of four 12-24 or 10-24 screws. Note The bottom hole of the shelf bracket should align with the bottom hole of a rack unit on the rack-mounting rail (the hole immediately above the 1/2-in. spacing). Step 2 Step 3 Step 4 Repeat with the other shelf bracket. Verify that the shelf brackets are at the same height (using the level or tape measure as desired). Attach the crossbar to the rear of the shelf brackets as shown in Figure A-1, using the 10-32 screws. Cisco MDS 9100 Series Hardware Installation Guide A-6 OL-17951-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Send documentation comments to [email protected]
A-6
Cisco MDS 9100 Series Hardware Installation Guide
OL-17951-02
Appendix A
Cabinet and Rack Installation
Cisco MDS 9000 Family Telco and EIA Shelf Bracket
To install the shelf brackets in a telco rack, follow these steps:
Step 1
Position a shelf bracket inside a rack-mounting rail as shown in
Figure A-1
and align the screw holes at
the front of the shelf bracket with the holes in the rack-mounting rail. Then attach the shelf bracket to
the rack-mounting rail using a minimum of four 12-24 or 10-24 screws.
Note
The bottom hole of the shelf bracket should align with the bottom hole of a rack unit on the
rack-mounting rail (the hole immediately above the 1/2-in. spacing).
Step 2
Repeat with the other shelf bracket.
Step 3
Verify that the shelf brackets are at the same height (using the level or tape measure as desired).
Step 4
Attach the crossbar to the rear of the shelf brackets as shown in
Figure A-1
, using the 10-32 screws.