HP Cisco MDS 9020 Cisco MDS 9100 Series Hardware Installation Guide (OL-17951- - Page 70

Removing a Cable from an SFP Transceiver,

Get HP Cisco MDS 9020 - Fabric Switch PDF manuals and user guides View all HP Cisco MDS 9020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Connecting to a Fibre Channel Port Chapter 3 Connecting the Cisco MDS 9100 Series Send documentation comments to [email protected] Figure 3-6 Connecting the LC-Type Cable to a Fibre Channel Port LC plug SFP module 91681 Caution If the cable does not install easily, ensure it is correctly oriented before continuing. For instructions on verifying connectivity, see the Cisco MDS 9000 Family Fabric Manager Configuration Guide and the Cisco MDS 9000 Family CLI Configuration Guide. Removing a Cable from an SFP Transceiver Caution When pulling a cable from a transceiver, grip the body of the connector. Do not pull on the jacket sleeve, because this can compromise the fiber-optic termination in the connector. Caution If the cable does not remove easily, ensure that any latch present on the cable has been released before continuing. To remove the cable, follow these steps: Step 1 Step 2 Step 3 Step 4 Attach an ESD-preventive wrist strap and follow its instructions for use. Press the release latch on the cable, grasp the connector near the connection point, and gently pull the connector from the transceiver. Insert a dust plug into the cable end of the transceiver. Insert a dust plug onto the end of the cable. Cisco MDS 9100 Series Hardware Installation Guide 3-8 OL-17951-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Send documentation comments to [email protected]
3-8
Cisco MDS 9100 Series Hardware Installation Guide
OL-17951-02
Chapter 3
Connecting the Cisco MDS 9100 Series
Connecting to a Fibre Channel Port
Figure 3-6
Connecting the LC-Type Cable to a Fibre Channel Port
Caution
If the cable does not install easily, ensure it is correctly oriented before continuing.
For instructions on verifying connectivity, see the
Cisco MDS 9000 Family Fabric Manager
Configuration Guide
and the
Cisco MDS 9000 Family CLI Configuration Guide
.
Removing a Cable from an SFP Transceiver
Caution
When pulling a cable from a transceiver, grip the body of the connector. Do not pull on the jacket sleeve,
because this can compromise the fiber-optic termination in the connector.
Caution
If the cable does not remove easily, ensure that any latch present on the cable has been released before
continuing.
To remove the cable, follow these steps:
Step 1
Attach an ESD-preventive wrist strap and follow its instructions for use.
Step 2
Press the release latch on the cable, grasp the connector near the connection point, and gently pull the
connector from the transceiver.
Step 3
Insert a dust plug into the cable end of the transceiver.
Step 4
Insert a dust plug onto the end of the cable.
LC plug
SFP module
91681