HP DL580 ProLiant DL580 Generation 4 Maintenance and Service Guide - Page 38

Removing a PCI latch

Get HP DL580 - ProLiant - G4 PDF manuals and user guides
UPC - 882780616011
View all HP DL580 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

3. Remove the PPM. IMPORTANT: Always install a PPM when you install a processor. The system fails to boot if the corresponding PPM is missing. To replace the component, reverse the removal procedure. Removing a PCI latch 1. Power down the server (on page 29). 2. Extend or remove the server from the rack ("Extending the server from the rack" on page 27, "Remove the server from the rack" on page 29). 3. Remove the access panel ("Removing the access panel" on page 29). CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all expansion slots have either an expansion slot cover or an expansion board installed. 4. Open the latch. 5. Remove the expansion board from the slot, if installed. 6. Remove the expansion slot cover from the slot, if installed ("Removing the expansion slot cover" on page 40). Removal and replacement procedures 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Removal and replacement procedures
38
3.
Remove the PPM.
IMPORTANT:
Always install a PPM when you install a processor. The system fails to boot if the
corresponding PPM is missing.
To replace the component, reverse the removal procedure.
Removing a PCI latch
1.
Power down the server (on page
29
).
2.
Extend or remove the server from the rack ("
Extending the server from the rack
" on page
27
,
"
Remove the server from the rack
" on page
29
).
3.
Remove the access panel ("
Removing the access panel
" on page
29
).
CAUTION:
To prevent improper cooling and thermal damage, do not operate the server unless
all expansion slots have either an expansion slot cover or an expansion board installed.
4.
Open the latch.
5.
Remove the expansion board from the slot, if installed.
6.
Remove the expansion slot cover from the slot, if installed ("
Removing the expansion slot cover
" on
page
40
).