HP DL580 ProLiant DL580 Generation 4 Maintenance and Service Guide - Page 52

Removing the power backplane

Get HP DL580 - ProLiant - G4 PDF manuals and user guides
UPC - 882780616011
View all HP DL580 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

6. Remove the screws securing the SAS hard drive cage. 7. Slowly pull the SAS hard drive cage out of the server until there is enough room to reach behind the SAS hard drive cage. 8. Disconnect all cables from the back of the SAS hard drive cage ("Hot-plug SAS and SATA hard drive cabling" on page 96). 9. Remove the mounting screws, and pull the SAS backplane from the rear of the cage. To replace the component, reverse the removal procedure. Removing the power backplane 1. Power down the server (on page 29). 2. Remove all power supplies ("Removing a redundant hot-plug power supply" on page 56) and power supply blanks ("Removing a power supply blank" on page 55). Removal and replacement procedures 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Removal and replacement procedures
52
6.
Remove the screws securing the SAS hard drive cage.
7.
Slowly pull the SAS hard drive cage out of the server until there is enough room to reach behind the
SAS hard drive cage.
8.
Disconnect all cables from the back of the SAS hard drive cage ("
Hot-plug SAS and SATA hard
drive cabling
" on page
96
).
9.
Remove the mounting screws, and pull the SAS backplane from the rear of the cage.
To replace the component, reverse the removal procedure.
Removing the power backplane
1.
Power down the server (on page
29
).
2.
Remove all power supplies ("
Removing a redundant hot-plug power supply
" on page
56
) and power
supply blanks ("
Removing a power supply blank
" on page
55
).