HP DL580 ProLiant DL580 Generation 4 Maintenance and Service Guide - Page 53

Removing the memory backplane

Get HP DL580 - ProLiant - G4 PDF manuals and user guides
UPC - 882780616011
View all HP DL580 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

NOTE: If you remove or replace the primary hot-plug power supply, use the T-15 Torx screwdriver provided with the server to remove the shipping screw. It is located just under the port-colored plastic handle of the power supply unit. 3. Extend or remove the server from the rack ("Extending the server from the rack" on page 27, "Remove the server from the rack" on page 29). 4. Remove the access panel ("Removing the access panel" on page 29). 5. Remove the system cage ("Removing the system cage" on page 31). 6. Loosen the thumbscrew, and remove the power backplane from the server. To replace the component, reverse the removal procedure. Removing the memory backplane 1. Power down the server (on page 29). 2. Remove all memory boards ("Removing a memory board" on page 67, "Removing a memory board (non-hot-plug)" on page 65). 3. Remove the processor module ("Removing the processor module" on page 33). 4. Extend or remove the server from the rack ("Extending the server from the rack" on page 27, "Remove the server from the rack" on page 29). 5. Remove the access panel ("Removing the access panel" on page 29). Removal and replacement procedures 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Removal and replacement procedures
53
NOTE:
If you remove or replace the primary hot-plug power supply, use the T-15 Torx
screwdriver provided with the server to remove the shipping screw. It is located just under the
port-colored plastic handle of the power supply unit.
3.
Extend or remove the server from the rack ("
Extending the server from the rack
" on page
27
,
"
Remove the server from the rack
" on page
29
).
4.
Remove the access panel ("
Removing the access panel
" on page
29
).
5.
Remove the system cage ("
Removing the system cage
" on page
31
).
6.
Loosen the thumbscrew, and remove the power backplane from the server.
To replace the component, reverse the removal procedure.
Removing the memory backplane
1.
Power down the server (on page
29
).
2.
Remove all memory boards ("
Removing a memory board
" on page
67
, "
Removing a memory board
(non-hot-plug)
" on page
65
).
3.
Remove the processor module ("
Removing the processor module
" on page
33
).
4.
Extend or remove the server from the rack ("
Extending the server from the rack
" on page
27
,
"
Remove the server from the rack
" on page
29
).
5.
Remove the access panel ("
Removing the access panel
" on page
29
).