HP DL580 ProLiant DL580 Generation 4 Maintenance and Service Guide - Page 55

Removing a power supply blank

Get HP DL580 - ProLiant - G4 PDF manuals and user guides
UPC - 882780616011
View all HP DL580 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

CAUTION: Always power down the server if the boot partition resides on the drive you are replacing or if you are replacing the only drive in the server. CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. 1. Determine the status of the hard drive from the hot-plug hard drive LEDs ("SAS and SATA hard drive LED combinations" on page 91). 2. Back up all server data on the hard drive to be removed. 3. Remove the hard drive. Removing a power supply blank NOTE: If you remove or replace the primary hot-plug power supply, use the T-15 Torx screwdriver provided with the server to remove the shipping screw. It is located just under the port-colored plastic handle of the power supply unit. Removal and replacement procedures 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Removal and replacement procedures
55
CAUTION:
Always power down the server if the boot partition resides on the drive you are
replacing or if you are replacing the only drive in the server.
CAUTION:
To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
1.
Determine the status of the hard drive from the hot-plug hard drive LEDs ("
SAS and SATA hard drive
LED combinations
" on page
91
).
2.
Back up all server data on the hard drive to be removed.
3.
Remove the hard drive.
Removing a power supply blank
NOTE:
If you remove or replace the primary hot-plug power supply, use the T-15 Torx
screwdriver provided with the server to remove the shipping screw. It is located just under the
port-colored plastic handle of the power supply unit.