HP Dragonfly Folio 13.5 Maintenance and Service Guide - Page 46

Remove the Phillips M1.6 × 1.6 screw, 4G WWAN module.

Get HP Dragonfly Folio 13.5 PDF manuals and user guides View all HP Dragonfly Folio 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

1. Remove the tape from the connectors on the module (1). 2. Loosen the two captive screws from the right fan (2). 3. Carefully disconnect the antenna cables from the connectors on the module (3). 4. Peel the gray conductive tape off the module (4). You can leave the tape connected to the connector. 5. Remove the Phillips M1.6 × 1.6 screw (5), and then pull the module out from under the plastic that extends over it from the thermal module (6). NOTE: 4G WWAN modules come with a reusable bracket. Be sure to use this bracket when installing a 4G WWAN module. 6. If the WWAN antenna is not connected to the terminal on the WWAN module, install a protective sleeve on the antenna connector, as shown in the following illustration. 40 Chapter 5 Removal and replacement procedures for authorized service provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
1.
Remove the tape from the connectors on the module
(1)
.
2.
Loosen the two captive screws from the right fan
(2)
.
3.
Carefully disconnect the antenna cables from the connectors on the module
(3)
.
4.
Peel the gray conductive tape off the module
(4)
. You can leave the tape connected to the connector.
5.
Remove the Phillips M1.6 × 1.6 screw
(5)
, and then pull the module out from under the plastic that
extends over it from the thermal module
(6)
.
NOTE:
4G WWAN modules come with a reusable bracket. Be sure to use this bracket when installing a
4G WWAN module.
6.
If the WWAN antenna is not connected to the terminal on the WWAN module, install a protective sleeve
on the antenna connector, as shown in the following illustration.
40
Chapter 5
Removal and replacement procedures for authorized service provider parts