HP Integrity Superdome SX1000 Site Preparation Guide, Fifth Edition - HP Integ - Page 25

Power Cords, PDCA Locations

Get HP Integrity Superdome SX1000 PDF manuals and user guides View all HP Integrity Superdome SX1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Figure 3-1 PDCA Locations Electrical Specifications Power Options PDCA 0 PDCA 1 60SP040A 8/20/01 Power Cords This section discusses the different possibilities for PDCA power cords. Pre-wired PDCAs Options 6 and 7 All servers are delivered with the appropriate cable and plug. The mating in-line connector is not provided. IMPORTANT Verify that the source power is correct for the appropriate PDCA wiring. NOTE When installing the power connector, allow enough room for mating the connector with the plug. Check the voltages at the connector prior to connecting the newly installed connector to the PDCA plug. Refer to Figure 3-3 and Figure 3-4 on page 19 for pin locations. Chapter 3 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Chapter 3
Electrical Specifications
Power Options
17
Figure 3-1
PDCA Locations
Power Cords
This section discusses the different possibilities for PDCA power cords.
Pre-wired PDCAs Options 6 and 7
All servers are delivered with the appropriate cable and plug. The mating in-line connector is not provided.
IMPORTANT
Verify that the source power is correct for the appropriate PDCA wiring.
NOTE
When installing the power connector, allow enough room for mating the connector with the
plug.
Check the voltages at the connector prior to connecting the newly installed connector to the PDCA plug. Refer
to Figure 3-3 and Figure 3-4 on page 19 for pin locations.
60SP040A
8/20/01
PDCA 0
PDCA 1