HP Pavilion dv3000 HP Pavilion dv3000 Entertainment PC - Maintenance and Servi - Page 76

Remove the heat sink

Get HP Pavilion dv3000 - Entertainment Notebook PC PDF manuals and user guides View all HP Pavilion dv3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Remove the heat sink: 1. Turn the system board upside down, with the battery connector toward you. 2. Loosen the two Phillips PM2.0×5.0 captive screws (1) that secure the heat sink to the system board 3. Lift the right side of the heat sink retention clip (2) until it rests at an angle. 4. Remove the heat sink retention clip (3) by sliding it to the right. NOTE: Due to the adhesive quality of the thermal material located between the heat sink and system board components, it may be necessary to move the heat sink from side to side to detach the assembly. 5. Remove the heat sink. NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink (1) and (2), the processer (3), and the graphics chip (4) each time the heat sink is removed. Thermal pads and thermal paste must be installed on all surfaces before the heat sink is reinstalled. Thermal pads and thermal paste are included with all heat sink, system board, and processor spare part kits. 68 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Remove the heat sink:
1
.
Turn the system board upside down, with the battery connector toward you.
2
.
Loosen the two Phillips PM2.0×5.0 captive screws
(1)
that secure the heat sink to the system board
3
.
Lift the right side of the heat sink retention clip
(2)
until it rests at an angle.
4
.
Remove the heat sink retention clip
(3)
by sliding it to the right.
NOTE:
Due to the adhesive quality of the thermal material located between the heat sink and
system board components, it may be necessary to move the heat sink from side to side to detach the
assembly.
5
.
Remove the heat sink.
NOTE:
The thermal material must be thoroughly cleaned from the surfaces of the heat sink
(1)
and
(2)
, the processer
(3)
, and the graphics chip
(4)
each time the heat sink is removed. Thermal pads and
thermal paste must be installed on all surfaces before the heat sink is reinstalled. Thermal pads and thermal
paste are included with all heat sink, system board, and processor spare part kits.
68
Chapter
4
Removal and replacement procedures