HP StorageWorks 2/16V Brocade Access Gateway Administrator's Guide - Supportin - Page 30

Using the CLI to disable Access Gateway mode, To disable Access Gateway mode

Get HP StorageWorks 2/16V - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/16V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

3 Disabling Access Gateway mode Using the CLI to disable Access Gateway mode After you disable Access Gateway mode, use the instructions in the Fabric OS Administrator's Guide to reconfigure the switch and join it to the fabric. Note Disabling Access Gateway mode clears the current Access Gateway mode configuration and reboots the switch. To disable Access Gateway mode 1. Connect and log in to the switch. 2. Enter the ag --modeshow command to verify that the switch is in Access Gateway mode. switch:admin> ag --modeshow Access Gateway mode is enabled 3. Enter the switchDisable command to disable the switch. switch:admin> switchdisable Note To save the Access Gateway configuration, use the configUpload command before proceeding with the next step. 4. Enter the ag command with the --modedisable operand to disable Access Gateway mode. switch:admin> ag --modedisable The switch automatically reboots and comes back online using the fabric switch configuration; the Access Gateway parameters, such as F_Port to N_Port mapping, failover, and failback policies are automatically removed. 5. Enter the ag --modeshow command to verify that Access Gateway mode has been disabled. switch:admin> ag --modeshow Access Gateway mode is NOT enabled Note Use the configDownload command to restore a previous fabric configuration. 3-4 Access Gateway Administrator's Guide Publication Number: 53-1000430-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
3-4
Access Gateway Administrator’s Guide
Publication Number: 53-1000430-01
Disabling Access Gateway mode
3
Using the CLI to disable Access Gateway mode
After you disable Access Gateway mode, use the instructions in the
Fabric OS Administrator’s Guide
to
reconfigure the switch and join it to the fabric.
To disable Access Gateway mode
1.
Connect and log in to the switch.
2.
Enter the
ag --modeshow
command to verify that the switch is in Access Gateway mode.
3.
Enter the
switchDisable
command to disable the switch.
4.
Enter the
ag
command with the
--modedisable
operand to disable Access Gateway mode.
The switch automatically reboots and comes back online using the fabric switch configuration; the
Access Gateway parameters, such as F_Port to N_Port mapping, failover, and failback policies are
automatically removed.
5.
Enter the ag --modeshow command to verify that Access Gateway mode has been disabled.
Note
Disabling Access Gateway mode clears the current Access Gateway mode configuration and reboots the
switch.
switch:admin> ag --modeshow
Access Gateway mode is enabled
switch:admin> switchdisable
Note
To save the Access Gateway configuration, use the
configUpload
command before
proceeding with the next step.
switch:admin> ag --modedisable
switch:admin> ag --modeshow
Access Gateway mode is NOT enabled
Note
Use the
configDownload
command to restore a previous fabric configuration.