HP StorageWorks 2/16V Brocade Access Gateway Administrator's Guide - Supportin - Page 53

Access Gateway system messages, AG-1001

Get HP StorageWorks 2/16V - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/16V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Access Gateway system messages D Access Gateway system messages AG-1001 Message , [AG-1001], ,, ERROR, , N_Port is connected to a fabric port that does not support NPIV Probable Cause Recommended Action Severity Indicates that the fabric port to which Access Gateway is connected does not support NPIV. Enable NPIV on the port connected to the Access Gateway using the portCfgNpivPort command on the fabric switch. Refer Fabric OS Command Reference Manual for more information on this command. ERROR AG-1002 Message , [AG-1002], ,, WARNING, , Unable to find alternate N_Port during fail over for N_Port Probable Cause Recommended Action Severity Indicates that the F_Ports could not be failed over because no other N_Ports are configured or that the fabric was unstable during the failover attempt. Verify whether or not other N_Ports are configured. If the message persists, run supportFtp to set up automatic FTP transfers; then run the supportSave command and contact your switch service provider. WARNING AG-1003 Message , [AG-1003], ,, WARNING, , Not able to fail over N_Port . Fail over across different fabric is not supported. Probable Cause Recommended Action Indicates that an F_Port could not be failed over to another N_Port because no other N_Ports were connected to the same fabric as N_Port that went offline. Connect two or more N_Ports to the same fabric and then enabled failover on these N_Ports using the ag --failoverenable command. Access Gateway Administrator's Guide D-5 Publication Number: 53-1000430-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Access Gateway Administrator’s Guide
D-5
Publication Number: 53-1000430-01
Access Gateway system messages
D
Access Gateway system messages
AG-1001
Message
Probable
Cause
Indicates that the fabric port to which Access Gateway is connected does not support NPIV.
Recommended
Action
Enable NPIV on the port connected to the Access Gateway using the
portCfgNpivPort
command on
the fabric switch. Refer
Fabric OS Command Reference Manual
for more information on this
command.
Severity
ERROR
AG-1002
Message
Probable
Cause
Indicates that the F_Ports could not be failed over because no other N_Ports are configured or that the
fabric was unstable during the failover attempt.
Recommended
Action
Verify whether or not other N_Ports are configured.
If the message persists, run
supportFtp
to set up automatic FTP transfers; then run the
supportSave
command and contact your switch service provider.
Severity
WARNING
AG-1003
Message
Probable
Cause
Indicates that an F_Port could not be failed over to another N_Port because no other N_Ports were
connected to the same fabric as N_Port that went offline.
Recommended
Action
Connect two or more N_Ports to the same fabric and then enabled failover on these N_Ports using the
ag --failoverenable
command.
<timestamp>, [AG-1001], <sequence-number>,, ERROR, <system-name>,
N_Port <port>
is connected to a fabric port that does not support NPIV
<timestamp>, [AG-1002], <sequence-number>,, WARNING, <system-name>,
Unable to find alternate N_Port during fail over for N_Port
<port
>
<timestamp>, [AG-1003], <sequence-number>,, WARNING, <system-name>,
Not able to fail over N_Port <port>. Fail over across different
fabric is not supported.