HP StorageWorks 8/80 HP StorageWorks Fabric OS 6.2.0g release notes (5697-0035 - Page 29

Initial setup of encrypted LUNs, Fabric OS 6.2.0 fixes, Table 7 Fabric OS 6.2.0 closed defects

Get HP StorageWorks 8/80 - SAN Switch PDF manuals and user guides View all HP StorageWorks 8/80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Initial setup of encrypted LUNs IMPORTANT: While performing first-time encryption to a LUN with more than one initiator active at the time, re-key operations slow to a standstill. Define LUNs for a single initiator at a time to avoid this occurrence. NOTE: When configuring multipath LUNs, care should be taken to add LUN0 on all of the paths, subject to the following considerations: • If LUN0 presented by backend target is a controller LUN (not a disk LUN; that is, not visible in the discoverLUN output), add LUN0 to the container as a clear text LUN. Make sure all of the paths have this LUN0 added for MPIO operation (EVA configuration, for example). • If LUN0 presented by the backend target is a disk LUN, LUN0 can be added to the container either as clear text or encrypted (MSA configuration, for example). • For HP-UX, LUN0 can appear as 0x0 or 0x400, but both of them are LUN0 only, and should be treated alike. Fabric OS 6.2.0 fixes The following table lists defects closed in the Fabric OS 6.2.0 firmware release. Table 7 Fabric OS 6.2.0 closed defects Closed defect summary Solution Add Member button is disabled while creating a new TI Zone when the switch is in VF mode. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Add Other Port button can be used to add ports. This is available in the ADD TI Zone window. Under stress testing, cfgsave takes a long time and fails to propagate on 64 VE-VE FCIP tunnel 33 switch core-edge topology running I/O. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Wait until fabric is not saturated to push configs around. Adding a B-series switch with conflicting domain ID into an EOS fabric may cause another switch to segment. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Check the domain ID before adding a switch to any fabric. USB port LED of HP StorageWorks DC SAN Backbone Director CP blade stays ON after HA failover. Fixed in Fabric OS 6.2.0. CUP Port stuck in Contingent Allegiance State after z9 Host IPL. Fixed in Fabric OS 6.2.0. Spinfab and porttest (diagnostics) are not supported on ICL ports. Fixed in Fabric OS 6.2.0. HP StorageWorks Fabric OS 6.2.0g release notes 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Initial setup of encrypted LUNs
IMPORTANT:
While performing first-time encryption to a LUN with more than one initiator active at the time, re-key
operations slow to a standstill. Define LUNs for a single initiator at a time to avoid this occurrence.
NOTE:
When configuring multipath LUNs, care should be taken to add LUN0 on all of the paths, subject to
the following considerations:
•
If LUN0 presented by backend target is a controller LUN (not a disk LUN; that is, not visible in the
discoverLUN
output), add LUN0 to the container as a clear text LUN. Make sure all of the paths
have this LUN0 added for MPIO operation (EVA configuration, for example).
•
If LUN0 presented by the backend target is a disk LUN, LUN0 can be added to the container
either as clear text or encrypted (MSA configuration, for example).
•
For HP-UX, LUN0 can appear as 0x0 or 0x400, but both of them are LUN0 only, and should be
treated alike.
Fabric OS 6.2.0 fixes
The following table lists defects closed in the Fabric OS 6.2.0 firmware release.
Table 7 Fabric OS 6.2.0 closed defects
Solution
Closed defect summary
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Add Other Port
button can be used to
add ports. This is available in the
ADD TI Zone window.
Add Member button is disabled while creating a new TI Zone when
the switch is in VF mode.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Wait until fabric is not saturated to
push configs around.
Under stress testing,
cfgsave
takes a long time and fails to propagate
on 64 VE-VE FCIP tunnel 33 switch core-edge topology running I/O.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Check the domain ID before adding
a switch to any fabric.
Adding a B-series switch with conflicting domain ID into an EOS fabric
may cause another switch to segment.
Fixed in Fabric OS 6.2.0.
USB port LED of HP StorageWorks DC SAN Backbone Director CP
blade stays ON after HA failover.
Fixed in Fabric OS 6.2.0.
CUP Port stuck in Contingent Allegiance State after z9 Host IPL.
Fixed in Fabric OS 6.2.0.
Spinfab and porttest (diagnostics) are not supported on ICL ports.
HP StorageWorks Fabric OS 6.2.0g release notes
29