HP StorageWorks 8/80 HP StorageWorks Fabric OS 6.2.0g release notes (5697-0035 - Page 32

StorageWorks DC SAN Backbone Director fan fault errors., B-series MP Router blade.

Get HP StorageWorks 8/80 - SAN Switch PDF manuals and user guides View all HP StorageWorks 8/80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

When disabling/enabling a port, port fencing disables the port because the allowable number of invalid transmission words is exceeded. Fixed in Fabric OS 6.2.0. Ag --show on an HP StorageWorks 8/8 or 8/24 SAN Switch shows incorrect edge switch IP address after a slave port is swapped with an N-port outside of the trunk group. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Reboot the switch and ag --show cli will show the correct output. The 32-character switchname and chassisname extensions do not fully display in RASLog outputs, such as errdump or supportsave output. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Use only 16-character switchname and chassisname fields if full name display in the logs is required. FFDC occurs when 16-31 char switch/chassis name is input on a platform that only supports up to 15. Fixed in Fabric OS 6.2.0. I2C response failure and subsequent reset occasionally results in HP StorageWorks DC SAN Backbone Director fan fault errors. Fixed in Fabric OS 6.2.0. Under some conditions N_Port Failover may not work when swapping trunked and non-trunked N_Ports on an Access Gateway. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Execute portdisable/portenable of F_Ports or switchdisable/switchenable or reboot the switch. Auto_ELP setting for EX_Port is not restored by configdownload. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Use auto_elp mode. When running stressful IRNDUP to CUP tests, user may observe Intermittent Channel Timeouts. Fixed in Fabric OS 6.2.0. Warnings of excessively high temperature seen on some HP StorageWorks 8/40 SAN switches. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Increase cooling or relocate switch to cooler location. Be sure switch is installed with proper spacing above and below it. POST (portloopback test) intermittently fails on 400 MP Router and B-series MP Router blade. Fixed in Fabric OS 6.2.0. Workaround prior to upgrade: Rerun diagnotics by rebooting the switch or powering on the slot with Bseries Multiprotocol Router blade. Zone Transaction appears to succeed in SMIA when the transaction was aborted by web GUI. Fixed in Fabric OS 6.2.0. Port address from switchshow does not include offset used for Interop mode 2. Fixed in Fabric OS 6.2.0. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Fixed in Fabric OS 6.2.0.
When disabling/enabling a port, port fencing disables the port be-
cause the allowable number of invalid transmission words is exceeded.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Reboot the switch and
ag --show
cli will show the correct output.
Ag --show
on an HP StorageWorks 8/8 or 8/24 SAN Switch shows
incorrect edge switch IP address after a slave port is swapped with
an N-port outside of the trunk group.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Use only 16-character switchname
and chassisname fields if full name
display in the logs is required.
The 32-character switchname and chassisname extensions do not fully
display in RASLog outputs, such as
errdump
or
supportsave
output.
Fixed in Fabric OS 6.2.0.
FFDC occurs when 16-31 char switch/chassis name is input on a
platform that only supports up to 15.
Fixed in Fabric OS 6.2.0.
I2C response failure and subsequent reset occasionally results in HP
StorageWorks DC SAN Backbone Director fan fault errors.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Execute
portdisable
/
porten-
able
of F_Ports or
switchdis-
able
/
switchenable
or reboot the
switch.
Under some conditions N_Port Failover may not work when swapping
trunked and non-trunked N_Ports on an Access Gateway.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Use auto_elp mode.
Auto_ELP setting for EX_Port is not restored by
configdownload
.
Fixed in Fabric OS 6.2.0.
When running stressful IRNDUP to CUP tests, user may observe Inter-
mittent Channel Timeouts.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Increase cooling or relocate switch to
cooler location. Be sure switch is in-
stalled with proper spacing above
and below it.
Warnings of excessively high temperature seen on some HP Storage-
Works 8/40 SAN switches.
Fixed in Fabric OS 6.2.0.
Workaround prior to upgrade:
Rerun diagnotics by rebooting the
switch or powering on the slot with B-
series Multiprotocol Router blade.
POST (
portloopback
test) intermittently fails on 400 MP Router and
B-series MP Router blade.
Fixed in Fabric OS 6.2.0.
Zone Transaction appears to succeed in SMIA when the transaction
was aborted by web GUI.
Fixed in Fabric OS 6.2.0.
Port address from
switchshow
does not include offset used for Interop
mode 2.
32