Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 520 » Manual Viewer

Husqvarna AUTOMOWER 520 Owner Manual - Page 50

LED indicator lamp on the charging station, 5 LED indicator lamp on the robotic lawnmower

View all Husqvarna AUTOMOWER 520 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

6.4 LED indicator lamp on the charging station For a fully functional installation, the indicator lamp in the charging station must emit a solid or flashing green light. If any other colour than green is visible, follow the troubleshooting guide below. There is more help on www.husqvarna.com. If you still need help, please contact your local Husqvarna representative. Light Solid green light Green flashing light Blue flashing light Red flashing light Solid red light Cause Action Good signals No action required The signals are good and ECO mode is acti- No action required. For more information on vated. ECO mode, see ECO mode on page 27. The boundary loop is not connected to the charging station. Check that the boundary wire connectors are fitted properly to the charging station. See Connecting the boundary wire on page 19. Break in the boundary loop. Find out where the break is. Replace the damaged section of the loop with a new loop wire and splice using an original coupler. Interruption in the charging station's antenna. Contact your local Husqvarna representative. Fault in the circuit board or incorrect power supply in the charging station. The fault should be rectified by an authorized service technician. Contact your local Husqvarna representative. 6.5 LED indicator lamp on the robotic lawnmower There is a LED indicator lamp on top of the robotic lawnmower, which shows the current status: Light Solid green light Solid blue light Solid yellow light Solid red light Flashing yellow light Cause Action The robotic lawnmower is either mowing the No action required. lawn, or leaving the charging station. The robotic lawnmower is either paused or parked, or is searching for the charging station. No action required. The STOP button has been pressed. Press the START button on top of the robotic lawnmower to start it again. The robotic lawnmower has stopped due to a fatal error. Clear the error by pressing the STOP button, and then activate the robotic lawnmower by pressing the START button on top of the robotic lawnmower. The robotic lawnmower requests the PIN code. The PIN code needs to be confirmed in the Automower® Connect app before the robotic lawnmower can be activated. There is more help on www.husqvarna.com. If you still need help, please contact your local Husqvarna representative. 50 - Troubleshooting 362 - 002 - 06.02.2018

Section	Page
Contents	2
Introduction	3
Memo	3
Product description	3
Capacity	3
Mowing technique	3
Working method	4
Movement pattern	4
Finding the charging station	4
Search method 1 - Irregular	4
Search method 2 - Follow guide wire	5
Search method 3 - Follow boundary wire	5
Product overview	6
Symbols on the product	7
Safety	8
Safety definitions	8
General safety instructions	8
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	8
Safety instructions for operation	8
Use	8
How to lift and move the robotic lawnmower	9
Maintenance	10
In the event of a thunderstorm	10
Installation	11
Presentation	11
Main components for installation	11
Preparations	11
Installation tools	12
Charging station	12
Best charging station location	12
Connecting the power supply	13
Installing and connecting the charging station	14
Charging the battery	14
Boundary wire	14
Plan where to lay the boundary wire	15
Working area boundaries	15
Boundaries within the working area	16
Secondary areas	17
Passages when mowing	17
Slopes	17
Laying the boundary wire	18
Eyelet for connecting the guide wire	18
Laying the boundary wire in towards the charging station	18
Splicing the boundary wire	19
Connecting the boundary wire	19
Installation of the guide wire	19
Laying and connecting the guide wire	20
Checking the installation	21
Connectivity	21
Automower® Connect	21
Getting started	21
Remote HMI	22
Husqvarna Fleet Services	22
How to start up the robotic lawnmower	22
First start-up sequence	22
Pairing with the Automower® Connect app	23
Guide calibration	23
Control panel	23
START and STOP button	23
The LED indicator lamp on the robotic lawnmower	23
Automower® Connect menu	23
Dashboard	23
Map	24
Map settings	24
Settings - overview	24
Timer	24
Timer suggestions Automower® 520	25
Timer suggestions Automower® 550	26
Edit timer settings	26
Edit current timer settings	26
Add a new timer setting	26
Cutting height	26
Operation	26
Weather timer	26
ECO mode	27
Spiral cutting	27
Installation	27
Finding the charging station	27
Charging station signal	28
Follow boundary wire	28
Follow guide wire	28
Guide > Disable / Enable	28
Lawn coverage	28
GPS assisted navigation	28
Area 1-5	28
Area 1-5 > Enable/disable	28
Area 1-5 > How? and How far?	28
Area 1-5 > How often?	28
Corridor width	29
Corridor width > Boundary	29
Corridor width > Guide	29
Exit angles	29
Exit angles > Sectors	29
Reversing distance	30
Drive past wire	30
Accessories	30
Mower house	30
Ultrasonic	30
General	30
Time & Date	30
Reset to factory settings	30
Security	30
New loop signal	30
Change PIN code	31
Theft protection	31
Alarm duration	31
Lifted	31
Turned upside down	31
STOP button pressed	31
Time lock	31
GeoFence	31
Automower® Connect	32
Overview of the settings structure (1)	33
Overview of the settings structure (2)	34
Overview of the settings structure (3) (Bluetooth short-range connectivity only)	35
Messages	36
My mowers	36
Yard layout examples	36
Open and level area	36
A number of islands and a 35% slope	37
L-shaped garden with a couple of islands and the charging station installed in the narrow area	37
U-shaped garden linked with a narrow passage	37
Unsymmetrical working area with a narrow passage and a number of islands	38
Three areas linked with two narrow passages	38
Large complex area with 3 guide wires	38
A secondary area	39
Operation	40
Main switch	40
Start	40
Operating mode - Start	40
Main area	40
Override timer	40
Secondary area	40
Operating mode - Park	41
Park until further notice	41
Start on next timer	41
Parking duration	41
The charging station's park button	41
Operating mode - Pause	41
Stop	41
Switch off	41
Charge a flat battery	42
Slope control	42
Maintenance	43
Introduction - maintenance	43
Clean the robotic lawnmower	43
Chassis and blade disc	43
Chassis	43
Wheels	43
Body	43
Charging station	43
Replace the blades	43
To replace the blades	44
Battery	44
Winter service	44
Troubleshooting	45
Introduction - troubleshooting	45
Fault messages	45
Information messages	48
LED indicator lamp on the charging station	50
LED indicator lamp on the robotic lawnmower	50
Symptoms	51
Finding breaks in the loop wire	52
Transportation, storage and disposal	55
Transportation	55
Winter storage	55
The robotic lawnmower	55
The charging station	55
After winter storage	55
Environmental information	55
Removal of battery for recycling	55
Technical data	57
Technical data	57
Warranty	59
Guarantee terms	59
EC Declaration of Conformity	60

Match case Limit results 1 per page

6.4 LED indicator lamp on the charging station

For a fully functional installation, the indicator lamp in the charging station must emit a solid or flashing green light. If

any other colour than green is visible, follow the troubleshooting guide below.

There is more help on www.husqvarna.com. If you still need help, please contact your local Husqvarna

representative.

Light

Cause

Action

Solid green light

Good signals

No action required

Green flashing light

The signals are good and

ECO mode

is acti-

vated.

No action required. For more information on

ECO mode

, see

ECO mode on page 27

Blue flashing light

The boundary loop is not connected to the

charging station.

Check that the boundary wire connectors are

fitted properly to the charging station. See

Connecting the boundary wire on page 19

Break in the boundary loop.

Find out where the break is. Replace the

damaged section of the loop with a new loop

wire and splice using an original coupler.

Red flashing light

Interruption in the charging station’s antenna.

Contact your local Husqvarna representative.

Solid red light

Fault in the circuit board or incorrect power

supply in the charging station. The fault

should be rectified by an authorized service

technician.

Contact your local Husqvarna representative.

6.5 LED indicator lamp on the robotic lawnmower

There is a LED indicator lamp on top of the robotic lawnmower, which shows the current status:

Light

Cause

Action

Solid green light

The robotic lawnmower is either mowing the

lawn, or leaving the charging station.

No action required.

Solid blue light

The robotic lawnmower is either paused or

parked, or is searching for the charging sta-

tion.

No action required.

Solid yellow light

The

STOP

button has been pressed.

Press the

START

button on top of the robotic

lawnmower to start it again.

Solid red light

The robotic lawnmower has stopped due to a

fatal error.

Clear the error by pressing the

STOP

button,

and then activate the robotic lawnmower by

pressing the

START

button on top of the ro-

botic lawnmower.

Flashing yellow light

The robotic lawnmower requests the PIN

code.

The PIN code needs to be confirmed in the

Automower

Connect app before the robotic

lawnmower can be activated.

There is more help on www.husqvarna.com. If you still need help, please contact your local Husqvarna

representative.

- Troubleshooting

362 - 002 - 06.02.2018