IBM 419452u Installation Guide - Page 35

Attention, Important

Get IBM 419452u - Servers System X3250 M2 Xeon 3.0ghz PDF manuals and user guides
UPC - 883436026604
View all IBM 419452u manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Attention: When you install an adapter, make sure that it is completely and correctly seated in the expansion slot in the riser card. Incomplete insertion might cause damage to the riser card, system board, or the adapter when you turn on the server. 7. Carefully grasp the adapter by its top edge or upper corners and align it with the expansion slot in the riser card assembly; then, press the adapter firmly into the expansion slot. Adapter bracket Expansion-slot bracket Tab Adapter Important: Make sure that the U-shaped opening in the metal adapter bracket engages the tab on the expansion-slot bracket. 8. Follow the cabling instructions, if any, that come with the adapter. 9. Reinstall the riser-card assembly. Make sure that the riser-card assembly is fully seated in the riser-card connectors on the system board. Power cable PCI-X slot 10. If you have installed an optional PCI-X riser-card assembly in the server, reconnect the riser-card power cable to the riser-card assembly. 11. If you are installing a ServeRAID-MR10i controller (2.5-inch drive models only), complete the following steps: a. Disconnect the existing SAS/SATA controller signal cable from the hard disk drive backplane and from the controller; then, remove the cable from the server. Chapter 2. Installing optional devices 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Attention:
When
you
install
an
adapter,
make
sure
that
it
is
completely
and
correctly
seated
in
the
expansion
slot
in
the
riser
card.
Incomplete
insertion
might
cause
damage
to
the
riser
card,
system
board,
or
the
adapter
when
you
turn
on
the
server.
7.
Carefully
grasp
the
adapter
by
its
top
edge
or
upper
corners
and
align
it
with
the
expansion
slot
in
the
riser
card
assembly;
then,
press
the
adapter
firmly
into
the
expansion
slot.
Adapter
Adapter
bracket
Expansion-slot
bracket
Tab
Important:
Make
sure
that
the
U-shaped
opening
in
the
metal
adapter
bracket
engages
the
tab
on
the
expansion-slot
bracket.
8.
Follow
the
cabling
instructions,
if
any,
that
come
with
the
adapter.
9.
Reinstall
the
riser-card
assembly.
Make
sure
that
the
riser-card
assembly
is
fully
seated
in
the
riser-card
connectors
on
the
system
board.
PCI-X slot
Power cable
10.
If
you
have
installed
an
optional
PCI-X
riser-card
assembly
in
the
server,
reconnect
the
riser-card
power
cable
to
the
riser-card
assembly.
11.
If
you
are
installing
a
ServeRAID-MR10i
controller
(2.5-inch
drive
models
only),
complete
the
following
steps:
a.
Disconnect
the
existing
SAS/SATA
controller
signal
cable
from
the
hard
disk
drive
backplane
and
from
the
controller;
then,
remove
the
cable
from
the
server.
Chapter
2.
Installing
optional
devices
21