Icom ID-52A About The Dv Gateway Function - Page 19

Operating in the Access Point mode

Get Icom ID-52A PDF manuals and user guides View all Icom ID-52A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

4 Access Point mode operation ■■Operating in the Access Point mode You can operate the Access Point transceiver as described below in the Access Point mode. What you can do while in the Terminal mode Display the RX HISTORY screen. Turn the Monitor function ON or OFF Open the MENU screen. Turn the Key Lock function ON or OFF. Open the Quick Menu* window. Audibly announce the displayed Call Sign. Select 1 MHz or 10 MHz tuning steps. Select the transmit output power. Adjust the audio volume level. Select an operating frequency. Turn the transceiver ON or OFF. Hold down [CD] for 1 second. Push [SQL]. LLRotate [DIAL] while pushing [SQL] to adjust the squelch level. A weaker signal than the set squelch level is not transmitted through the Internet. Push [MENU]. Hold down [LOCK] for 1 second. Push [QUICK]. Hold down [SPCH] for 1 second. LLHold down [QUICK] for 1 second when using the ID-31A PLUS/ID-31E PLUS. Push [VFO/MHz]. LLPush [V/MHz] when using the ID-31A PLUS/ID-31E PLUS/ ID-51A (PLUS2)/ID-51E (PLUS2). LLYou cannot select 10 MHz tuning steps in the ID-31A PLUS/ID-31E PLUS/ID-52A/ID-52E. Hold down [LOW] for 1 second to select the transmit output power between S-Low, Low1, Low2, Mid, and High. LLHold down [LO] for 1 second to open the Select Output Power window when using the ID-52A/ID-52E. LLNo icon appears when high power is selected. LL"SLO," "LO1," "LO2," or "MID" appears when S-low, Low 1, Low 2, or Mid power is selected. Rotate [VOL]. Rotate [DIAL]. Hold down [ ] for 1 second. LLThe Access Point mode is not automatically canceled even if you turn OFF the transceiver, then ON it again. * You can select the following items (Quick Menu window) in the Access Point mode. LL"Band Select" and "ATT" are not displayed when using the ID-31A PLUS/ID-31E PLUS. LL"ATT" is not displayed when using the ID-51A (PLUS2)/ID-51E (PLUS2). Band Select TS ATT GPS Information GPS Position Home CH Set Voltage TIP: See the transceiver's manual about each key operation. ID-31A PLUS/ID-31E PLUS Basic manual Section 2, 3, 11 Advanced manual Section 11 ID-51A (PLUS2)/ID-51E (PLUS2) Basic manual Section 2, 4, 6 Advanced manual Section 9 ID-52A/ID-52E Basic manual Section 2, 3, D-STAR OPERATION Advanced manual Section 5 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
4
Access Point mode operation
19
■
Operating in the Access Point mode
You can operate the Access Point transceiver as described below in the Access Point mode.
What you can do while in the Terminal mode
Display the RX HISTORY screen.
Hold down [CD] for 1 second.
Turn the Monitor function ON or OFF
Push [SQL].
L
Rotate [DIAL] while pushing [SQL] to adjust the squelch level.
A weaker signal than the set squelch level is not
transmitted through the Internet.
Open the MENU screen.
Push [MENU].
Turn the Key Lock function ON or OFF.
Hold down [LOCK] for 1 second.
Open the Quick Menu* window.
Push [QUICK].
Audibly announce the displayed Call Sign.
Hold down [SPCH] for 1 second.
L
Hold down [QUICK] for 1 second when using the ID-31A
PLUS/ID-31E PLUS.
Select 1 MHz or 10 MHz tuning steps.
Push [VFO/MHz].
L
Push [V/MHz] when using the ID-31A PLUS/ID-31E PLUS/
ID-51A (PLUS2)/ID-51E (PLUS2).
L
You cannot select 10 MHz tuning steps in the ID-31A
PLUS/ID-31E PLUS/ID-52A/ID-52E.
Select the transmit output power.
Hold down [LOW] for 1 second to select the transmit
output power between S-Low, Low1, Low2, Mid, and
High.
L
Hold down [LO] for 1 second to open the Select Output
Power window when using the ID-52A/ID-52E.
L
No icon appears when high power is selected.
L
“SLO,” “LO1,” “LO2,” or “MID” appears when S-low, Low 1,
Low 2, or Mid power is selected.
Adjust the audio volume level.
Rotate [VOL].
Select an operating frequency.
Rotate [DIAL].
Turn the transceiver ON or OFF.
Hold down [
] for 1 second.
L
The Access Point mode is not automatically canceled even
if you turn OFF the transceiver, then ON it again.
* You can select the following items (Quick Menu
window) in the Access Point mode.
L
“Band Select” and “ATT” are not displayed when using
the ID-31A PLUS/ID-31E PLUS.
L
“ATT” is not displayed when using the
ID-51A (PLUS2)/ID-51E (PLUS2).
<<Normal Mode>>
Band Select
TS
ATT
GPS Information
GPS Position
Home CH Set
Voltage
<<REC Start>>
<<GPS Logger Only>>
TIP:
See the transceiver’s manual about each key
operation.
ID-31A PLUS/ID-31E PLUS
Basic manual Section 2, 3, 11
Advanced manual Section 11
ID-51A (PLUS2)/ID-51E (PLUS2)
Basic manual Section 2, 4, 6
Advanced manual Section 9
ID-52A/ID-52E
Basic manual Section 2, 3, D-STAR OPERATION
Advanced manual Section 5