Intel H2000WP Technical Product Specification - Page 24

AC Input Specification

Get Intel H2000WP PDF manuals and user guides View all Intel H2000WP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Power Sub-System Intel® Server Chassis H2000 Family TPS Pin Description 9 Return Sense 11 +12V Remote Sense 13 Reserved 15 +12VSB Pin Description 10 PWOK 12 Compatibility Bus 14 +12VSB 16 Key Pin (removed) 3.2 AC Input Specification 3.2.1 Input Voltage And Frequency The power supply must operate within all specified limits over the following input voltage range. Harmonic distortion of up to 10% THD must not cause the power supply to go out of specific limits. The power supply shall be capable of start-up (power-on) with full rated power load, at line voltage as low as 90VAC. Table 12. AC input rating Parameter Min Rated Max Start up VAC Power Off VAC 110VAC 90 Vrms 100-127 Vrms 140 Vrms 85 VAC± 4VAC 70VAC±5VAC 220VAC 180 Vrms 200-240 Vrms 264 Vrms Frequency 47 Hz 50/60 Hz 63 Hz Note: 1. Maximum input current at low input voltage range shall be measured at 90VAC, at max load. 2. Maximum input current at high input voltage range shall be measured at 180VAC, at max load. 3. This requirement is not to be used for determining agency input current markings. 3.2.2 AC input Power Factor The power supply must meet the power factor requirements stated in the Energy Star® Program Requirements for Computer Servers. These requirements are stated below. Table 13. Typical power factor Output power Power factor 10% load > 0.80 20% load 50% load 100% load > 0.90 > 0.90 > 0.95 Note: Tested at 230Vac, 50Hz and 60Hz and 115VAC, 60Hz. Tested according to Generalized Internal Power Supply Efficiency Testing Protocol Rev 6.4.3. This is posted at http://efficientpowersupplies.epri.com/methods.asp. 3.2.3 Efficiency The following table provides the required minimum efficiency level at various loading conditions. These are provided at three different load levels; 100%, 50%, 20%, and 10%. Output shall be load according to the proportional loading method defined by 80 Plus in Generalized Internal Power Supply Efficiency Testing Protocol Rev 6.4.3. This is posted at: http://efficientpowersupplies.epri.com/methods.asp. 14 Revision 1.0 Intel order number: G59059-001

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
Power Sub-System
Intel
®
Server Chassis H2000 Family TPS
Revision 1.0
Intel order number: G59059-001
14
Pin
Description
Pin
Description
9
Return Sense
10
PWOK
11
+12V Remote Sense
12
Compatibility Bus
13
Reserved
14
+12VSB
15
+12VSB
16
Key Pin (removed)
3.2
AC Input Specification
3.2.1
Input Voltage And Frequency
The power supply must operate within all specified limits over the following input voltage range.
Harmonic distortion of up to 10% THD must not cause the power supply to go out of specific
limits. The power supply shall be capable of start-up (power-on) with full rated power load, at
line voltage as low as 90VAC.
Table 12. AC input rating
Parameter
Min
Rated
Max
Start up VAC
Power Off VAC
110V
AC
90 V
rms
100-127 V
rms
140 V
rms
85 V
AC
± 4V
AC
70V
AC
±5V
AC
220V
AC
180 V
rms
200-240 V
rms
264 V
rms
Frequency
47 Hz
50/60 Hz
63 Hz
Note:
1. Maximum input current at low input voltage range shall be measured at 90VAC, at max load.
2. Maximum input current at high input voltage range shall be measured at 180VAC, at max load.
3. This requirement is not to be used for determining agency input current markings.
3.2.2
AC input Power Factor
The power supply must meet the power factor requirements stated in the Energy Star
®
Program
Requirements for Computer Servers. These requirements are stated below.
Table 13. Typical power factor
Output power
10% load
20% load
50% load
100% load
Power factor
> 0.80
> 0.90
> 0.90
> 0.95
Note
: Tested at 230Vac, 50Hz and 60Hz and 115VAC, 60Hz. Tested according to Generalized
Internal Power Supply Efficiency Testing Protocol Rev 6.4.3. This is posted at
.
3.2.3
Efficiency
The following table provides the required minimum efficiency level at various loading conditions.
These are provided at three different load levels; 100%, 50%, 20%, and 10%. Output shall be
load according to the proportional loading method defined by 80 Plus in Generalized Internal
Power Supply Efficiency Testing Protocol Rev 6.4.3. This is posted at:
.