Invacare XLT Owners Manual - Page 35

Adjusting Top End XLT Gold Hand Crank

Get Invacare XLT PDF manuals and user guides View all Invacare XLT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

SECTION 6-RIDING POSITION Adjusting Top End XLT Gold Hand Crank NOTE: For this procedure, refer to FIGURE 6.5. Adjusting Hand Crank Height 1. Loosen, but DO NOT remove the hex nut securing the hand crank to the fork stem. 2. Loosen, but DO NOT remove the two set screws for the upper clamp. 3. Move the hand crank assembly up or down in the fork neck until you are comfortable with the position for operational purposes. NOTE: The hand crank should be positioned so that when the hand is toward the front of the handcycle, the arm is slightly bent. The arm should NEVER be fully extended (locked) at any point while cranking. 4. Tighten the hex nut to secure the hand crank in the desired position. 5. Tighten the two set screws on the upper clamp. 6. Tighten the chain if necessary. Refer to Adjusting Seven Speed Hub Chain on page 55 or Adjusting Twenty‐Seven Speed Cassette Chain on page 56. Hex Nut Fork Neck Upper Clamp and Set Screws Hand Crank (Gear and Chain Not Shown) FIGURE 6.5 Adjusting Top End XLT Gold Hand Crank Part No 1114850 35 Recumbent Handcycle Series

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
SECTION 6—RIDING POSITION
Part No 1114850
35
Recumbent Handcycle Series
Adjusting Top End XLT Gold Hand Crank
NOTE: For this procedure, refer to FIGURE 6.5.
Adjusting Hand Crank Height
1.
Loosen, but DO NOT remove the hex nut securing the hand crank to the fork stem.
2.
Loosen, but DO NOT remove the two set screws for the upper clamp.
3.
Move the hand crank assembly up or down in the fork neck until you are comfortable
with the position for operational purposes.
NOTE: The hand crank should be positioned so that when the hand is toward the front of the
handcycle, the arm is slightly bent. The arm should NEVER be fully extended (locked) at any point
while cranking.
4.
Tighten the hex nut to secure the hand crank in the desired position.
5.
Tighten the two set screws on the upper clamp.
6.
Tighten the chain if necessary. Refer to Adjusting Seven Speed Hub Chain
on page 55
or Adjusting Twenty
‐
Seven Speed Cassette Chain
on page 56.
FIGURE 6.5
Adjusting Top End XLT Gold Hand Crank
Hex
Nut
Fork Neck
Upper Clamp
and Set
Screws
Hand Crank
(Gear and Chain Not Shown)