Kenwood VRS-N8100 Instruction Manual - Page 14

CAUTION, Protection circuitry, Connecting the speakers - test

Get Kenwood VRS-N8100 - AV / Digital Multimedia Receiver PDF manuals and user guides
UPC - 019048156235
View all Kenwood VRS-N8100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Preparations Setting up the system Connecting the speakers CAUTION Make sure that the power cord plug is disconnected from the AC wall outlet before proceeding to speaker cord connections. If the conductor wires on the extremity of speaker cord are untwisted, there is a risk of short-circuiting. Be sure to twist them well before connecting the speaker cord. Whether each speaker is connected properly can be confirmed by outputting the test tone and checking if each speaker channel outputs audio. For details, see "Speaker settings" (Step 6 Adjust the speaker volume level). £ Protection circuitry This unit incorporates protection circuitry, which may be activated during high-power reproduction or in case of extreme rise in temperature. When the protection circuitry is activated, the output from this unit is shut down and the STANDBY indicator blinks. In this case, turn this unit OFF then ON again and reduce the output volume level. Front Speakers Surround Speakers Be sure to connect both surround speakers. Right Left Center Speaker Right Surround Back Speaker When the surround back speaker is connected to these terminals, set the speaker setting to "BS/ SW Amp Back Surr.". ™ Left In this case, the subwoofer should be connected to the PRE OUT SUBWOOFER jack. ^ Subwoofer When the subwoofer is connected to these terminals, set the speaker setting to "BS/SW Amp Subwoofer". ™ In this case, two surround back speakers should be connected to the PRE OUT SURROUND BACK jacks. ^ SPEAKERS (6-8Ω) CENTER SURR R SURR BACK SURR L /SW R FRONT L 14 EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
14
EN
Preparations
SPEAKERS (6
-
8
Ω
)
R
L
FRONT
CENTER
SURR R
SURR BACK
/SW
SURR L
Setting up the system
Front Speakers
Surround Speakers
Be sure to connect both surround speakers.
Surround Back Speaker
When the surround back speaker is connected to
these terminals, set the speaker setting to
"
BS/
SW Amp Back Surr.
".
™
In this case, the subwoofer should be connected
to the
PRE OUT SUBWOOFER
jack.
^
Subwoofer
When the subwoofer is connected to these termi-
nals, set the speaker setting to
"
BS/SW Amp
Subwoofer
".
™
In this case, two surround back speakers should be
connected to the
PRE OUT SURROUND BACK
jacks.
^
Center
Speaker
Left
Right
Left
Right
Whether each speaker is connected properly can be
confirmed by outputting the test tone and checking if
each speaker channel outputs audio. For details, see
"Speaker settings" (Step
6
Adjust the speaker volume
level).
£
CAUTION
Make sure that the power cord plug is disconnected from the AC
wall outlet before proceeding to speaker cord connections.
If the conductor wires on the extremity of speaker cord are
untwisted, there is a risk of short-circuiting. Be sure to twist
them well before connecting the speaker cord.
Protection circuitry
This unit incorporates protection circuitry, which may be activated
during high-power reproduction or in case of extreme rise in tempera-
ture.
When the protection circuitry is activated, the output from this unit is
shut down and the
STANDBY
indicator blinks.
In this case, turn this unit OFF then ON again and reduce the output
volume level.
Connecting the speakers