Kenwood VRS-N8100 Instruction Manual - Page 21

Preparing for playback Preparations 4 Select the setup method. Speaker Setup 1 Select "Speaker Setup" and press the ENTER key (or the Enter key) to select the speaker setup method. 2 Use the MULTI CONTROL @ / # (or the Multi @ / # keys) for the following displays. 4QFBLFS
4FUVQ HTB 1 HTB 2 HTB 3 Custom Exit 6.1ch 5.1ch 6.1ch 5.1ch 6.1ch 5.1ch C L SW LS BS R RS RECEIVER SETUP SPEAKER SETUP HTB1 6.1ch 1 "HTB1 6.1CH": Select "HTB1 6.1CH" if you use speaker system KS-3100EX. * 2 "HTB1 5.1CH": Select "HTB1 5.1CH" if you use speaker system KS-2100HT. * 3 "HTB2 6.1CH": Select "HTB2 6.1CH" if you use speaker system KS-708HT+KS-308EX or KS-308HT+KS-308EX. * 4 "HTB2 5.1CH": Select "HTB2 5.1CH" if you use speaker system KS-708HT or KS-308HT. * 5 "HTB3 6.1CH": Select "HTB3 6.1CH" if you use speaker system KS-908EX. * 6 "HTB3 5.1CH": Select "HTB3 5.1CH" if you use speaker system KS-908HT.* 7 "Custom": Select to set up the speakers according to the speaker system in use. (Speaker setup is required every time after the speaker system is changed.) 8 "Exit": Select "Exit" and press the ENTER (or the Enter key) to return to the previous display. * Model availability may differ depending on the country and sales area. ÷ When the 5.1 channel speaker system configuration is used or the speaker setting is set to "BS/SW Amp Off", the PL IIx, DTS-ES and DOLBY EX listen modes cannot be selected. If you selected "HTB1 6.1CH", "HTB1 5.1CH", "HTB2 6.1CH", "HTB2 5.1CH", "HTB3 6.1CH" or "HTB3 5.1CH" in the above: Press the ENTER (or the Enter key), then press the MULTI CONTROL % / fi (or the Multi % / fi keys) to select "Yes", and press the ENTER (or the Enter key) again to establish the setup. ÷ Select "No" to return to the status before setup. ÷ When you use a KENWOOD speaker system and select "HTB1 6.1CH", "HTB1 5.1CH", "HTB2 6.1CH", "HTB2 5.1CH", "HTB3 6.1CH" or "HTB3 5.1CH" set the speaker setup, the audio will be corrected automatically according to the speaker characteristics. If you selected "Custom" in the above: Press the ENTER (or the Enter key) to proceed to detailed setups. After this, continue the procedure from step 5. The flow of the SETUP is as follows; SPEAKER SETUP SPEAKER LEVEL Speaker Distance Assignment HTB 1 6.1CH HTB 1 5.1CH HTB 2 6.1CH HTB 2 5.1CH HTB 3 6.1CH HTB 3 5.1CH Custom Exit Subwoofer Test Tone Auto Left Center Right Right Surr. Back Surr. (RB/ LB) Left Surr. Subwoofer Meters Feet Exit Left Center Digital Input Component Video Exit LEF Level Game Exit Function Mode 1 Mode 2 Off Front Center Surround Back Surr. BS/SW Amp SW Re-mix Test Tone Manual Test Tone Off Left Center Right Right Surr. Back Surr. (RB/ LB) Left Surr. Subwoofer Exit Right Right Surr. Back Surr. (RB/ LB) Left Surr. Subwoofer 5 Select a speaker system. 1 Use the MULTI CONTROL % / fi (or the Multi % / fi keys) to select the appropriate subwoofer setting. 4QFBLFS
4FUVQ
$VTUPN Subwoofer On C L SW LS BS R RS RECEIVER SETUP SPEAKER SETUP SUBWOOFER ON 1 "Subwoofer On": When a subwoofer is connected. 2 "Subwoofer Off": When no subwoofer is connected. ÷ The initial setting is "Subwoofer On". ÷ When "Subwoofer Off" is selected and the selection is estab- lished by pressing the MULTI CONTROL # (or the Multi # key) in step 2 below, the front speakers are set automatically to "Front Large" and the procedure jumps to step 5. 2 Use the MULTI CONTROL # (or the Multi # key) to accept the setting. 3 Use the MULTI CONTROL % / fi (or the Multi % / fi keys) to select the appropriate front speakers setting. 1 "Front Large": Large front speakers are connected to the receiver. Continued to next page 21 EN