Kenwood VRS-N8100 Instruction Manual - Page 22
Preparations, Preparing for playback, Continued to next
UPC - 019048156235
View all Kenwood VRS-N8100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
Preparations Preparing for playback 2 "Front Normal": Average size front speakers are connected to the receiver. ÷ When the subwoofer setting is "Subwoofer On", front speakers setting is "Front Large" and a stereo source is played, the low frequencies may be reproduced through the front speakers and no audio output from the subwoofer in certain listen modes. In this case, set the subwoofer re-mix setting in step # to "SW Re-mix On" to output the low frequencies from the subwoofer. 4 Use the MULTI CONTROL # (or the Multi # key) to accept the setting. 5 Use the MULTI CONTROL % / fi (or the Multi % / fi keys) to select the appropriate center speaker setting. 1 "Center Large": * A large center speaker is connected to the receiver. 2 "Center Normal": An average size center speaker is connected to the receiver. 3 "Center Off": When no center speaker is connected. * "Center Large" cannot be selected when the front speakers have been set to "Front Normal". 6 Use the MULTI CONTROL # (or the Multi # key) to accept the setting. 7 Use the MULTI CONTROL % / fi (or the Multi % / fi keys) to select the appropriate surround speaker setting. 1 "Surround Large": Large surround speakers are connected to the receiver. 2 "Surround Normal": Average size surround speakers are connected to the receiver. 3 "Surround Off": When no surround speakers are connected. ÷ When "Surround Off" is selected and the selection is established by pressing the MULTI CONTROL # in step 8 below, the procedure jumps to step #. However, if the subwoofer setting is "Subwoofer Off", the procedure jumps to step $ so that you can complete the speaker setup and proceed to the speaker volume level adjustment in step 6. 8 Use the MULTI CONTROL # (or Multi # key) to accept the setting. 9 Use the MULTI CONTROL % / fi (or the Multi % / fi keys) to select appropriate surround back speaker setting. 1 "Back Surr. Large": * Large surround back speaker is connected to the receiver. 2 "Back Surr. Normal": Average size surround back speaker is connected to the receiver. 3 "Back Surr. Off": When no surround back speakers is connected. * "Back Surr. Large" cannot be selected when the sur- round speaker has been set to "Surround Normal" or "Surround Off". 22 EN 0 Use the MULTI CONTROL # (or the Multi # key) to accept the setting. ! Use the MULTI CONTROL % / fi (or the Multi % / fi keys) to select the appropriate BS/SW amp setting. 1 "BS/SW Amp Back Surr.": Select this setting when a surround back speaker is connected to the SURR BACK/SW terminals. In this case, the subwoofer signal will be output from the PRE OUT SUBWOOFER jack. 2 "BS/SW Amp Subwoofer": Select when the subwoofer speaker is connected to the SURR BACK/SW terminals. In this case, the surround back signals will be output from the PRE OUT SURROUND BACK jacks. 3 "BS/SW Amp Off": Select when no speaker is connected to the SURR BACK/ SW terminals. In this case, the subwoofer signal will be output from the PRE OUT SUBWOOFER jack and the surround back signals will be output from the PRE OUT SURROUND BACK jacks. ÷ If "BS/SW Amp Back Surr." is selected, only one surround back speaker can be connected to the receiver. ÷ If "BS/SW Amp Subwoofer" or "BS/SW Amp Off" is selected, two surround back speakers can be connected to the PRE OUT SURROUND BACK jacks through an external power amplifier. ^ @ Use the MULTI CONTROL # (or the Multi # key) to accept the setting. # Use the MULTI CONTROL % / fi (or the Multi % / fi keys) to select the appropriate subwoofer re-mix setting. If "SW Re-mix On" is selected as the subwoofer re-mix setting, the low frequencies are enhanced by adding the low frequencies of other channels to the subwoofer channel or adding the low frequencies of the subwoofer to other channels depending on the speaker setup. 1 "SW Re-mix On": Subwoofer re-mix setting mode to the receiver is ON. 2 "SW Re-mix Off": Subwoofer re-mix setting mode to the receiver is OFF. ÷ The initial setting is "SW Re-mix On". ÷ The subwoofer re-mix setting is possible only when the subwoofer setting is "Subwoofer On" and the front speaker setting is "Front Large". $ Press the ENTER (or the Enter key). If your selection is correct, press the MULTI CONTROL % / fi (or the Multi % / fi key) to select "Yes". Press the ENTER (or the Enter key) again to return to the main setup displays. ÷ Select "No" and press the ENTER (or the Enter key) to return to the status before setup. Continued to next page