Kenwood VRS-N8100 Instruction Manual - Page 23

Preparing for playback 6 Adjust the speaker volume level. Speaker Level From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. ÷ In this step 6, only the speaker channels that have been set and require the volume level adjustment are displayed. 1 Use the MULTI CONTROL @/# (or the Multi @/# keys) to select "Speaker Level" on setup displays, and press the ENTER (or the Enter key). 2 Use the MULTI CONTROL @/# (or the Multi @/# keys) to select "Test Tone Auto", "Test Tone Manual " or "Test Tone Off". 4QFBLFS
-FWFM Test Tone Test Tone Test Tone Auto Manual Off Exit RECEIVER SETUP SPEAKER LEVEL TEST TONE AUTO 1 "Test Tone Auto": Select this setting to adjust the speaker volume levels using the test tone. The test tone will be output from every speaker channel in automatic sequence. 2 "Test Tone Manual": Select the speaker channel to output the test tone using the MULTI CONTROL@ / # (or the Multi @ / # key). 3 "Test Tone Off": Select to adjust the speaker volume levels using the current output signals. The speaker channel to output the signal can be selected using the MULTI CONTROL@ / # (or the Multi @ / # key). 4 "Exit": Select "Exit" and press the ENTER (or the Enter key) to return to the previous display. ÷ Press the SETUP (or Setup) key to cancel the SETUP mode in the middle. When "Test Tone Auto" or "Test Tone Manual" is selected and the ENTER (or the Enter key) is pressed again, the test tone output will start. Use the MULTI CONTROL % / fi (or the Multi % / fi keys) to adjust the volume level of the test tone output from the speaker channel to be adjusted. For "Test Tone Auto" selection, the first test tone is heard from the front left speaker for 2 seconds. The next test tone is heard from the speakers in the following sequence for 2 seconds each. When the "BS/SW Amp Back Surr." has been selected: Left Center Right Right Surround Subwoofer Left Surround Back Surround When the "BS/SW Amp Subwoofer" or "BS/SW Amp Off" has been selected: Left Center Right Right Surround Subwoofer Left Surround Left Back Surround Right Back Surround Left 0 dB 5FTU
5POF
"VUP 00 dB L 00 dB SW LS 00 dB C 00 dB BS 00 dB R 00 dB 00 dB RS SPEAKER LEVEL TEST TONE AUTO LEFT 0dB ÷ If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. e ÷ When a speaker setup is set to off the volume level for the corresponding speakers is reset to 0 dB. When "Test Tone Manual" or "Test Tone Off" is selected, press the MULTI CONTROL @/# (or the Multi @/# key) to select the speaker channel and then press the MULTI CONTROL %/fi (or the Multi %/fi key) to adjust the speaker volume level. 5FTU
5POF
.BOVBM
Left 0 dB 00 dB L 00 dB SW LS 00 dB C 00 dB BS 00 dB R 00 dB 00 dB RS SPEAKER LEVEL TEST TONE MANUAL LEFT 0dB 3 Press the ENTER (or the Enter key) again to return to the main setup displays. ÷ The test tone is turned off and return to the main setup displays. 7 Input the distance to the speakers. Speaker Distance This setting allows the signals output from different speakers to reach the listening position simultaneously. ÷ In this step 7, only the speaker channels that have been set and require the volume level adjustment are displayed. Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to Front speaker (L) : ____ feet (meters) Distance to Center speaker (C) : ____ feet (meters) Distance to Front speaker (R) : ____ feet (meters) Distance to Surround speaker (RS) : ____ feet (meters) Distance to Surround back speaker (RB) : ____ feet (meters) Distance to Surround back speaker (LB) : ____ feet (meters) Distance to Surround speaker (LS) : ____ feet (meters) Distance to Subwoofer (SW) : ____ feet (meters) Continued to next page 23 EN Preparations