Konica Minolta AccurioPress 6120 AccurioPress 6136/6136P/6120 Daily Maintenanc - Page 108

AccurioPress 6136/6136P/6120

3-39

3.6

Details of quality adjustment items

3

8

Press [OK] to complete the setting.

%

To cancel the change, press [Cancel]. In either case, the screen returns to the [Quality Adjustment

Menu] screen.

NOTICE

If you press [Cancel], the maximum density measurement result is not saved.

3.6.6

[Max. Density Auto Adj.]

The Maximum Density Auto Adjustment is:

-

When

Intelligent Quality Optimizer IQ-501

is provided, the density is automatically adjusted using

In-

telligent Quality Optimizer IQ-501

.

-


is not provided, the density is adjusted using

Relay Unit RU-518

.

This section describes how to make adjustments using

Relay Unit RU-518

without

Intelligent Quality Op-

timizer IQ-501

.

The maximum density is automatically adjusted by scanning the printed charts using the density control sen-

sor mounted on

Relay Unit RU-518

.

NOTICE

Be sure to use the paper for registering a desired density to perform Max. Density Auto Adj.. With an unreg-

istered paper, the adjustment cannot be performed correctly.

If you want to perform automatic adjustment using paper other than a registered paper, you need to register

a desired density again. For details, contact your service representative.

Be sure to perform Color Density Manual Control after changing the maximum density.

Tips

-

After Max. Density Auto Adj., the paper profile used for automatic adjustment changes to the one used

for registering a desired density; the profile does not return to the one before adjustment. You can ask

a service engineer to specify the setting so that after this adjustment the paper profile automatically re-

turns to the one before adjustment. For details, contact your service representative.

-

When


is not mounted on the machine [Max. Density Auto Adj.

(RU)] is displayed.

1

Press [Adjustment] on the [MACHINE] screen to display the [Adjustment Menu] screen.

2

Press [Quality Adjustment] and [Max. Density Auto Adj. (RU)] in sequence.

Section	Page
Table of contents	4
1 Daily Care	7
1.1 Daily Cleaning	7
Care timing	7
Care requirements	7
1.2 Weekly Cleaning	8
Care timing	8
Care requirements	8
1.3 Cleaning the Scanning Area	9
1.4 Cleaning the Fusing Unit	11
1.5 Cleaning the Duplex Part	14
1.6 Cleaning the Output Unit	20
1.7 Cleaning the Paper Feed Unit	23
2 Both Sides Adjust	27
2.1 What is Both Sides Adjust?	27
2.2 Adjustment flow to use paper of a new brand, weight, or size	28
2.2.1 Adjustment Timing	28
2.2.2 Adjustment Order	28
2.3 Regular adjustment flow	29
2.3.1 Adjustment Timing	29
2.3.2 Adjustment Order	29
2.3.3 Periodical Both Sides Adjustment Function	30
2.4 Adjustment flow for each job	31
2.4.1 Adjustment Timing	31
2.4.2 Adjustment Order	31
2.5 How to Operate the Both Sides Adj. Item	32
2.5.1 Fine-adjusting the gap between side guide plates of Paper Feed Unit PF-710	32
2.5.2 [Front] Adjustment	36
2.5.3 [Scan Meas.] Adjustment	41
2.5.4 [Rotate/Skew] Adjustment	49
2.5.5 [Gap] Adjustment (Back side adjustment)	52
2.5.6 [AutoMeasure] Adjustment	57
2.5.7 Registering Paper Profile	59
2.5.8 Back Side Fine Adjustment	62
2.5.9 [Periodical Both Sides Adj.]	67
3 Quality Adjustment	71
3.1 Quality Adjustment for Image Controller	71
3.2 Regular adjustment flow (Standard)	72
3.2.1 Adjustment timing	72
3.2.2 Adjustment sequence	72
3.3 Regular adjustment flow (High accuracy)	73
3.3.1 Adjustment Timing	73
3.3.2 Adjustment Order	73
3.4 Adjustment flow to use a new type of paper	74
3.4.1 Adjustment timing	74
3.4.2 Adjustment sequence	74
3.5 Adjustment Flow when changing the screen	75
3.5.1 Adjustment timing	75
3.5.2 Adjustment sequence	75
3.6 Details of quality adjustment items	76
3.6.1 Setting of the Custom Screen	76
3.6.2 [Gamma Automatic Adj.]	78
Performing [Gamma Automatic Adj.]	78
3.6.3 [Density Balance Adjustment]	80
Adjustment flow when changing the screen	80
Saving the measured data of the density balance	90
Registering the adjusted value of the density balance in the machine	91
3.6.4 [Density Balance Auto. Adj.]	97
3.6.5 [Maximum Density Adjustment]	106
3.6.6 [Max. Density Auto Adj.]	108
3.6.7 Checking the Color Density Control Setting	110
3.6.8 [Color density manual control]	112

Konica Minolta AccurioPress 6120 AccurioPress 6136/6136P/6120 Daily Maintenanc - Page 108

[Max. Density Auto Adj.]

Page 108 highlights